manualshive.com logo in svg

Schleuniger CrimpCenter 64 SP, Original Operating Manual, Page: 225 / 346

Share
Download
Schleuniger CrimpCenter 64 SP Original Operating Manual Download Page 225

9. Servicing / Maintenance

Original Operating Manual | Edition 1.0 (01-2020) | CrimpCenter 64 SP

225 | 268

9.6

MAINTENANCE SHEET - CHECK MACHINE

Check Machine

Task

Check and log the entire machine.

Unit

Entire machine

Duration

approx. 20 min.

Interval

Yearly

Personnel qualifica-

tion

Qualified Personnel

Within the scope of preventive maintenance the machine has to be checked for technical

intactness and completeness. Likewise, the attachment or anchoring of the machine to its

substructure or footprint must be checked.

Only proper machines are safe!
Record the result!

The maintenance interval depends on the use of the machine, but has to be executed at

least once a year.
It is recommend taking the checks into the operator instruction.

WARNING

Personnel Qualification and Personal Protective Equipment!

The following instructions are to be followed!

The test and report may only be executed by technical specialists.

See also chapter “Personnel Qualification” and “Personal Protective

Equipment”.

Element

Status / Condition / Position

Main Switch

On

Emergency stop switch (All)

Not pressed

Control voltage

On

Safety Cover

This side up

EASY Software

Started and logged in

Summary of Contents for CrimpCenter 64 SP



























































































































































































































































































































































Reviews:

No comments