manualshive.com logo in svg

Schleuniger CrimpCenter 64 SP, Original Operating Manual, Page: 214 / 346

Share
Download
Schleuniger CrimpCenter 64 SP Original Operating Manual Download Page 214

9. Servicing / Maintenance

214 | 268

Original Operating Manual | Edition 1.0 (01-2020) | CrimpCenter 64 SP

9.5.8

Motors

» Standstill Monitoring

Task

Check the standstill monitoring of the motors.

Duration

-

Interval

-

Personnel qualifica-

tion

Qualified Personnel

1.

▹

The operating company has to make sure that the safety devices are checked yearly

according to the following instruction.

➥

The checks must be recorded.

➥

It is recommend taking the checks into the operator instruction.

Should one of the tests be negative, you must follow the following points!

Stop the machine immediately!
Immediately contact the service of Schleuniger!

WARNING

Personnel Qualification and Personal Protective Equipment!

The following instructions are to be followed!

The test and report may only be executed by technical specialists.

See also chapter “Personnel Qualification” and “Personal Protective

Equipment”.

Element

Status / Condition / Position

Main Switch

On

Emergency stop switch (All)

Not pressed

Control voltage

On

Safety Cover

This side up

EASY Software

Started and logged in

Before the test is carried out, it must be changed into the following EASY menu.

Press the following button:

Summary of Contents for CrimpCenter 64 SP



























































































































































































































































































































































Reviews:

No comments