manualshive.com logo in svg

SCHIEBEL ACTUSAFE CMFS, Operating Manual, Page: 12 / 99

Share
Download
SCHIEBEL ACTUSAFE CMFS Operating Manual Download Page 12

7 Commissioning

Operating Manual Linear ACTUSAFE CMFS(L)

OM-ENGLISH-Failsafe-Linear-16xx-V2.00-2022.03.03

7

Commissioning

It is assumed that the actuator has been installed and electrically connected correctly. (See section 4, page 27)

NOTE:

Remove silica gel from the alarm cover.

7.1

General information

Technical data

Type

Max. actuators torque

[

Nm

]

Revolutions on the base actuator

In failsafe

direction

Counter

failsafe

direction

nominal

[

mm

]

Revolutions

[

U

]

maximal

[

mm

]

Revolutions

[

U

]

CM03FS(L)30_5

8

16

30

6

35

7

CM03FS(L)50_8

16

32

50

10

55

11

CM03FS(L)100_12

16

32

100

20

105

21

CM06FS(L)100_30

24

64

100

25

105

26,25

CM06FS(L)170_25

24

64

170

42,5

108

45

NOTE:

When commissioning and each time after dismounting the actuator, the electrical end positions have to be reset

(see chapter 5.5, page 31).

7.2

Manual operation

The manual operation is only possible if the actuator is delivered with the optional handwheel. This option allows an ad-
justment of the valve in de-energized state.

CAUTION:

The manual mode can be activated only when the drive is in the failsafe position.

CAUTION:

By activating the manual drive the failsafe function is disabled.

NOTE:

By activating the manual drive the electrical function of the drive is disabled. In normal operation, the hand wheel

(9) has no effect, it rotates idly by.

12

Summary of Contents for ACTUSAFE CMFS




































































































Reviews:

No comments