Scheppach 5801102904, Manual

Page: 28 / 40


www.scheppach.com /

service@scheppach.com /

+(49)-08223-4002-99 /

+(49)-08223-4002-58
28 | GB
24. Avoid overheating of the saw teeth.
25. When sawing plastic, avoid melting of the plas-
tic. Use the appropriate saw blades for this pur-
pose. Replace damaged or worn saw blades im-
mediately. When the saw blade overheats, stop
the machine. Allow the saw blade to cool down
before using the power tool again.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with unpro-
tected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur -
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected expo-
sure to the beam can occur.
• If you do not use the device for a long time, the
batteries should be removed.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.
Safety instructions for handling batteries
1. Always make sure that the batteries are inserted
with the correct polarity (+ and –), as indicated
on the battery.
2. Do not short-circuit batteries.
3. Do not charge non-rechargeable batteries.
4. Do not overcharge batteries!
5. Do not mix old and new batteries or batteries
of different types or manufacturers! Replace an
entire set of batteries at the same time.
6. Immediately remove used batteries from the de-
vice and dispose of them properly! Do not dis-
pose batteries with household waste. Defective
or used batteries must be recycled according to
Directive 2006/66 / EC. Give back batteries and
/ or the device has been offered to the collective
facilities. About disposal facilities you can inform
by your municipal or city government.
7. Do not allow batteries to heat up!
8. Do not weld or solder directly on batteries!
9. Do not dismantle batteries!
10. Do not allow batteries to deform!
11. Do not throw batteries into fire!
may cause the saw head to be suddenly pulled
downward, causing a risk of injury.
Safety Instructions for the handling of saw blades
1. Do not use damaged or deformed saw blades.
2. Do not use any insertion tools with cracks. Sort
out cracked insertion tools. Repairs are not per-
mitted.
3. Do not use saw blades made of high speed steel.
4. Check the condition of the saw blades before us-
ing the cross cut mitre saw.
5. Make sure that a suitable saw blade for the ma-
terial to be cut is selected.
6. Only use saw blades recommended by the man-
ufacturer. Saw blades designed to cut wood and
similar materials must comply with EN 847-1.
7. Do not use saw blades made of high-speed alloy
steel (HSS steel).
8. Only use saw blades for which the maximum
permissible speed is not lower than the maxi-
mum spindle speed of the cross cut mitre saw
and which are suitable for the material to be cut.
9. Observe the saw blade direction of rotation.
10. Only insertion the saw blade if you have mas-
tered their use.
11. Observe the maximum speed. The maximum
speed specified on the insertion tool may not
be exceeded. If specified, observe the speed
range.
12. Clean grease, oil and water off of the clamping
surfaces.
13. Do not use any loose reducing rings or bushes
for the reducing of holes on saw blades.
14. Make sure that fixed reducer rings for securing
the insertion tool have the same diameter and
have at least 1/3 of the cutting diameter.
15. Make sure that fixed reducer rings are parallel
to each other.
16. Handle insertion tool with caution. They are ide-
ally stored in the originally package or special
containers. Wear protective gloves in order to
improve grip and to further reduce the risk of
injury.
17. Prior to the use of insertion tools, make sure that
all protective devices are properly fastened.
18. Prior to use, make sure that the insertion tool
meets the technical requirements of this electric
tool and is properly fastened.
19. Only use the supplied saw blade for cutting
wood, never for the processing of metals.
20. Only use saw blade diameters in accordance
with the markings on the saw.
21. Use additional workpiece supports, if required
for workpiece stability.
22. Workpiece support extensions must always be
secured and used during work.
23. Replace table inserts when worn!