background image

5

2016-08-25 / V1.0

Connectors UIC 558 – Installation and Maintenance Instructions

Dangers and Security Measures

3.  Dangers and Security Measures

3.1  Electrical Dangers

  DANGER

The connectors contain components that carry voltage. Risk of electric shock!

Always observe the following safety regulations before beginning any work on electrical 

 

constructions:

 

X

Disconnect 

 

X

Ensure that it is not possible to reconnect unintentionally

 

X

Clearly mark your work area

 

X

Make sure that there is no voltage present

 

X

Earth and short circuit the installation

 

X

Insulate or cover adjacent energized parts

 

X

Only an electrically skilled person may determine if there is no voltage present

  WARNING

Dirt, moisture, snow and ice in the interior of coupling receptacles or dummy receptacles contami-

nate the plug. The coupling of a contaminated plug to the coupling receptacle may lead to electric 

shock, short circuit and damage to the connectors!

 

X

Always check if the interior of the receptacles is free from dirt, moisture, snow and ice before 

inserting a plug into a coupling receptacle or a dummy receptacle.

 

X

Do not insert a plug into a receptacle when the latter is contaminated, moist or contaminated 

with snow and ice.

 

X

Remove dirt, moisture, snow and ice without residues from the interior of receptacles and from 

the plug.

 

X

Never couple a contaminated plug to the coupling receptacle.

3.2  Other Dangers

  WARNING

Exclusively use the connectors for purposes as indicated in the specications and data sheets. 

A wrong application can cause accidents and severe damages to persons.

 

X

The manufacturer doesn‘t take the responsibility for accidents which were caused by improper 

use of the product.

 

X

We recommend the use of fault current safety systems in constructions with voltages higher 

than safety extra-low voltage.

  WARNING

The plugging and disconnecting of the connectors on-load can cause electric arcs. When explosive 

substances or ignition sources of any kind are nearby, there is a risk of fire and explosion!

 

X

Never plug and disconnect the connectors on-load.

Summary of Contents for UIC Series



























Reviews: