background image

20

2016-08-25 / V1.0

Plugging Procedure

Connectors UIC 558 – Installation and Maintenance Instructions

6.1  Plugging

 

X

Open the hinged lid (3) of the coupling receptacle 

(4). 

In doing so, observe the opening angle:

 

-

at least 110 °

 

-

but not more than 130 °

max. 130 °

min. 110 °

3

4

Fig. 20:  Open the hinged lid (3) of the coupling receptacle (4): 

Opening angle at least 110 °, at most 130 °

 

X

Position the plug (5) in such a way that the arrow 

(6) on the plug is congruent with the arrow (7) on 

the hinged lid of the coupling receptacle (4).

6

7

4

5

Fig. 21:  Align arrow (6) on plug congruent with arrow (7) on 

the receptacle lid

Then insert the plug in such a way that the guide-

ways (2) in the plug slide without much effort into 

the slots (1) of the receptacle (refer to 

Fig. 19

). 

In doing so, take care

 

-

that plug and receptacle are aligned axially (a 

plug set diagonally by more than 8 ° cannot be 

plugged by hand anymore!),

 

-

that the plug is completely (flush) inserted in 

the receptacle.

 

X

After that close the hinged lid (3) by hand until the 

locking mechanism (8) on lid and plug latches.

3

8

Fig. 22:  Close the hinged lid (3) by hand until the locking 

mechanism (8) on lid and plug latches

6.2  Unplugging

 

X

Open the hinged lid (3) of the coupling receptacle 

(4). In doing so, observe the opening angle:

 

-

at least 110°

 

-

but not more than 130° 

 

X

Hold the hinged lid (3) and take off the plug (5) 

from receptacle (4). Only pull on the plug, not on 

the cable.

 

X

Close the hinged lid (3) by hand until the locking 

mechanism (9) on lid and receptacle shell latches.

3

9

9

4

Fig. 23:  Close the hinged lid (3) of the coupling receptacle (4) 

by hand until the locking mechanism (9) latches

Summary of Contents for UIC Series



























Reviews: