background image

SCARAB M25H ROAD SWEEPER - Abbreviated Operating Instructions

Normal drive mode

No unauthorised or untrained personnel to operate this sweeper.

1. Select Neutral (Yellow Control Lever). Handbrake ON. Sweep Mode 

switch OFF. Multi-function lever OFF. Start Engine.

2. Select Forward or Reverse (Yellow Control Lever).
3. Release handbrake, press accelerator pedal to move the vehicle. 

Sweep mode

4. Stop vehicle. Handbrake ON.
5. Sweep Mode switch ON. Engine RPM changes to pre-set level.
6. Select the desired sweeping equipment. Switch on Suction Fan.

Suction Fan speed (2000 RPM). Use Engine speed controls to change RPM if required. 

7. Multi-function lever ON, beacons ON.
8. Select FORWARD (Yellow Control Lever). Handbrake OFF, depress accelerator pedal to move 

vehicle.

All sweeping equipment will stop and raise when REVERSE is selected, and re-engage in 
FORWARD.

Cruise control (only in sweep mode)

9. With vehicle at the desired speed, select Cruise Control. Can be over-ridden by the 

accelerator pedal, and is cancelled by using the foot brake or by pressing the switch.

When sweeping with a full load or up-hill, engine RPM may need to be increased.

Vehicle movement is controlled, by means of the accelerator and brake pedal, similar to a 
vehicle fitted with automatic transmission. 

Never press brake and accelerator pedals at the same time. 

This document is designed as a quick reference guide, to allow the operator to drive the vehicle 
in Normal or Sweep Mode and operate the basic controls. It does not constitute the full 
operating instructions.

Forward

Reverse

Neutral

!

F1

F1

F2

F2

F3

F3

1267

12:34

LCD Screen

Cruise control ON

Work light ON

Sweep mode ON

Suction active

Side brush active

Water ON

Engine RPM

Time

Central brush (wide sweep)

water ON

Main equipment colour codes

Equipment not selected

Equipment pre-selected

Equipment operating (active)

Water pre-selected

Equipment and water pre-selected

NOTE:

 LCD screen is shown with the majority of icons shown to give a representation 

of what could be visible and is not what would be visible in normal use.

Main Control Panel

!

Sweep mode 

ON

Suction fan 

ON

Hopper

not down

H-P water pump

Water tank 

level low

H-P water pump

no water

Hydraulic oil 

low

Hydraulic oil 

temperature

Service 

reminder

Active fault 

present

Press and hold down the Safety Interlock and the 
appropriate control switch.

For safety reasons only operate the Remote 
Control from outside the vehicle, from a vantage 
point that affords a good view of the sweeper and 
its surroundings.

LEVER UP (OFF)

, Stop and raise all sweeping 

equipment.

LEVER MIDDLE (ON)

, Deploy all selected 

sweeping equipment.

LEVER RIGHT

, right front brush OUT/IN.

LEVER LEFT

, left front brush OUT/IN.

LEVER DOWN (NOZZLE TILT)

For a temporary nozzle tilt pull lever back and 
hold to OPEN.
Release the lever to CLOSE.

 

Main on-screen information

and warning symbols

Auxiliary Control Panel

Remote Control

= Option*

= Raise hopper

= Lower hopper

= Open rear door*

= Close rear door*

= Safety interlock

Sweep mode

Front brush water*

Front brush*

Left suction

Left side brush

Left work light

Engine speed -

Engine speed +

Left water

Option*

Option*

Central brush

(wide sweep) water

Right water

Right work light

Right side brush

Suction fan

Option*

Central brush
(wide sweep)

* = Option

* = Option

* = Option

Not applicable

Multi-function lever

Favourite setting

Nozzle tilt locked

High pressure

water pump

Cruise control

OFF

ON

Left 
front 
brush

Right 
front 
brush

Nozzle 

tilt

Right suction

Please refer to reverse for health and safety advice

Reviews: