manualshive.com logo in svg

Scantronic iNSIGHT 20, Operator'S Manual, Page: 94 / 167

Share
Download
Scantronic iNSIGHT 20 Operator'S Manual Download Page 94

Chapter 4: Maintenance

Maintenance Schedule

Operator’s Guide

83

Maintenance Schedule

Use the following table as a guide to routine maintenance. 

Usage figures are not guaranteed. Customer-operating 

environments, document type, the condition of 

documents being scanned, and not following the 

recommended cleaning and replacement procedures, can 

cause the life of the consumables to vary. 

Procedure

Interval

What to Use

Clean separator module 

tires

As required 

depending on the 

type of scanning 

being performed.

Use staticide wipe (part number 

830 9783) -- slightly damp. 

Allow to air dry before 

scanning.

Clean feed module tires

As required 

depending on the 

type of scanning 

being performed.

Use staticide wipe, (part number 

830 9783) -- slightly damp. 

Allow to air dry before 

scanning.

Clean drive rollers and 

transport area

As required 

depending on the 

type of scanning 

being performed.

Run transport cleaning sheet, 

(part number 896 2201). If 

required, use emulsiclean wipe, 

(part number 137 4966) on red 

and white rollers. Allow to air 

dry. 

CAUTION:

DO NOT USE THE 

EMULSICLEAN WIPE 

ON THE GRAY FOAM 

TIRES. 

Clean imaging guides

Daily

Use staticide wipe, (part number 

830 9783) -- slightly damp. Wipe 

with a dry staticide wipe before 

scanning.

Summary of Contents for iNSIGHT 20








































































































































































Reviews:

No comments