manualshive.com logo in svg

Scantronic iNSIGHT 20, Operator'S Manual, Page: 100 / 167

Share
Download
Scantronic iNSIGHT 20 Operator'S Manual Download Page 100

Chapter 4: Maintenance

Running a Transport Cleaning Sheet

Operator’s Guide

89

Running a Transport Cleaning Sheet

NOTE: 

The scanner must be closed and powered on to run a 

transport cleaning sheet.

1.

Remove the wrapping from the Transport Cleaning 

Sheet.

2.

Adjust the side guides to fit the cleaning sheet.

3.

Place a transport cleaning sheet in the input tray 

(adhesive side up) in portrait orientation.

4.

Using your scanning application, scan the transport 

scanning sheet.

5.

After the transport cleaning sheet is scanned, turn it 

over and scan it again.

6.

Repeat this procedure, if necessary until all residue is 

removed from the drive rollers. If you are unable to 

remove all residue from the drive rollers using the 

transport cleaning sheet, perform the procedure 

described in “Cleaning the Rollers and Transport” on 

page 90.

7.

When a transport cleaning sheet gets very dirty, 

discard it and use a new one.

8.

When you are done running transport cleaning sheets, 

open the scanner and check that the imaging guides 

are clean.  If necessary, clean the imaging guides as 

described in “Cleaning the Imaging Guides” on 

page 94.

Summary of Contents for iNSIGHT 20








































































































































































Reviews:

No comments