Scania DI14 69 Operator'S Manual Download

Page: 11 / 55

2001-05:1

The illustrations show a typical DI14 69 engine configuration.

Your engine may have different equipment from the one shown.

Type plate

Engine serial number,
punched in engine block

Oil cooler

Oil dipstick

Oil cleaner

Oil filter, turbo

Drain plug, engine oil

Coolant pump

Charge air cooler (engine
coolant-cooled)

10.

Turbocharger

11.

Injection pump

12.

Fuel filter

13.

Starter motor

14.

Alternator

15.

Fan belt, adjuster

16.

Coolant pipes to turbo

17.

Inspection holes, engine
block

18.

Drain cock, coolant

19.

Oil filler cap

20.

Seawater pump

21.

Heat exchanger

22.

Sacrificial anodes

23.

Expansion tank with pres-
sure cap

24.

Oil pressure monitor

25.

Charge air cooler (seawa-
ter-cooled)

26.

Seawater pipe to charge air
cooler

19 23 22

Summary of Contents for DI14 69
























































Search results

Summary of Contents for DI14 69

Reviews:

Related manuals for DI14 69

Brands by name

Popular brands

Scania DI14 69, Operator'S Manual

Search results

Summary of Contents for DI14 69

Reviews:

Related manuals for DI14 69

Brands by name

Popular brands