Scaled Instruments Davis 7747 Manual Download Page 1

 

© 2014 Scaled Instruments – Reproduction prohibited unless permission explicitly granted 

www.scaledinstruments.com 

 

 

www.scaledinstruments.com 

507 NW 60th Street Suite D Gainesville, FL, 32607 USA 
Phone: (352) 262-6119 
Email: [email protected] 

 

 

24-Hour Conversion Kit for the Davis Instruments 7747 

Daytime Fan-Aspirated Radiation Shield

 

Table of Contents 

Introduction .................................................................................................................................................. 1 
Acknowledgements ....................................................................................................................................... 2 
Components .................................................................................................................................................. 2 
Parts List ........................................................................................................................................................ 2 
Tools Needed: ............................................................................................................................................... 2 
Performing the Conversion ........................................................................................................................... 3 

Installation Overview ................................................................................................................................ 3 
Remove & Disassemble the existing DFARS ............................................................................................. 3 
Move Spacers ............................................................................................................................................ 9 
Install Battery Terminals into appropriate slots ..................................................................................... 11 
Place the PCBA into the DFARS and Solder battery connectors ............................................................. 13 
Reassemble the radiation shield ............................................................................................................. 15 
Reinstall the radiation shield to the ISS .................................................................................................. 19 

 

Introduction 

 

Thank you for your purchase of the 24-hour conversion kit used to convert a Davis 7747 
Daytime Fan-Aspirated Radiation Shield (DFARS) into a 24-hour unit.  This conversion kit is 
designed to bring your DFARS as close as possible to the official 24-hour shield used on the 
Davis Vantage Pro2 Models 6153 & 6163.  The kit utilizes the same parts used in these models 
to provide both solar and battery power to your DFARS.  This guide assumes you have already 
purchased and installed the Davis 7747 unit.  Scaled Instruments is not responsible for any 

Summary of Contents for Davis 7747





















Reviews: