SBG Navsight Apogee IMU Hardware Manual Download Page 31 | Manualshive

Page: 31 / 74

background image

Navsight Solution

– Hardware Manual

NAVSIGHTHM.1.3

5.2. Rack version Overview

The rack version of Navsight present the same interfaces and capabilities as the rugged one. Following
diagrams show the different interfaces available on a Navsight processing unit. Front face is dedicated to
quick user access to main functions and status indication.

The back face of Navsight processing unit is used to hold all electrical connections. A single connector is
generally dedicated to a single interface to enable easy connections on various systems. Standard
connectors enable easy connection with the third party systems.

31/74

Figure 5.3: Navsight Rack Processing unit front face user interface

Figure 5.4: Navsight rack processing unit back face interfaces

«
...
29
30
31
32
33
...
»

Summary of Contents for Navsight Apogee IMU











































































Reviews:

No comments

Related manuals for Navsight Apogee IMU

Brand: XOVision Pages: 24

CENTRAL ELO-16 GB

Brand: Tyco Fire Product Pages: 4

Brand: First Power Pages: 16

Brand: MNC Pages: 32

Brand: Xtrons Pages: 24

Brand: Alpine Pages: 19

Brand: Viking Pages: 9

Brand: Pioneer Pages: 7

Brand: Pioneer Pages: 112

Brand: Pioneer Pages: 110

Brand: 10-8 Video Pages: 29

Brand: Polaris Pages: 24

Brand: Trust Pages: 6

GMX550 LOCKPICK

Brand: Coastal Electronic Pages: 10

Brand: Audiovox Pages: 12

Brand: Audiovox Pages: 15

Brand: Audiovox Pages: 18

VOD8521 - DVD Player / LCD Monitor

Brand: Audiovox Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands