manualshive.com logo in svg

SBC PCD2.M5 Series, Manual

Share
Download
SBC PCD2.M5 Series Manual Download Page 34

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

Mounting

PCD2.M5_ Classic CPUs and expansion housings

3-21

3

3.5.4  Remove upper part of housing

To install (new or replacement) communications interfaces, the upper part of the 

housing has to be removed.

● 

Disconnect all cables (USB, Ethernet, Profibus, RS-232).

 

● 

Remove housing cover (see Section 3.5.2 Removing the housing cover)

 

● 

Pull out plug-in screw terminal blocks (X3…X6)

 

● 

Unscrew the two TORX Plus 10IP bolts (for the position of the two bolts, see 

 

 

below)

 

● 

Remove upper part of housing

Torx 10

Torx 10

Optional communication interfaces

To simplify customer installation, optional communication interfaces should be 

ordered together with the PCD2.M5_. Up to two PCD7.F1xx units can be plugged into 

Slots A#1 and A#2.

The following PCD7.F1xx communication modules can be plugged into Slots A#1 and 

A#2:

A#1

A#2

X4-Port 1 

1. PCD7.F1xx

X3-Port 2 

2. PCD7.F1xx

 

● PCD7.F110

 

● PCD7.F121

 

(PCD7.F120 must not be used)

 

● PCD7.F130

 

● PCD7.F150

 

● PCD7.F180

Summary of Contents for PCD2.M5 Series





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands