SBC PCD2.M5 Series Manual Download Page 31

Page: 31 / 244

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

Mounting

PCD2.M5_ Classic CPUs and expansion housings

3-18

3.5

Mounting

The PCD2 can be snapped onto two top-hat rails (2 x 35 mm). The PCD2 can also

be screwed to any other flat surface with 4 M4 screws; the grooves provided for this

purpose can be accessed by lifting off the snap-on cover.

Mounting the PCD2 on the top-hat rail



Press bottom of housing onto the mounting surface



Press upwards against the top-hat rail



Press top of housing against the mounting surface and snap into

place



Push the housing down onto the top-hat rail to ensure that it is

secure

Removal

To remove the housing, push upwards and pull out.

3.5.1 Mounting position and ambient temperature

A vertical surface is normally used to mount the module carrier; the I/O connections

to the modules then also run vertically. In this mounting position, the ambient

temperature may be from 0 °C to 55°C. In all

other positions, air convection works

less well, and an ambient temperature von 40 °C should not be exceeded











Summary of Contents for PCD2.M5 Series





















































































































































































































































Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands

SBC PCD2.M5 Series, Manual

Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands