manualshive.com logo in svg

SBC PCD2.M5 Series, Manual, Page: 185 / 244

Share
Download
SBC PCD2.M5 Series Manual Download Page 185

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

Analogue output modules, electrically isolated

Input/output (I/O) modules

6-74

6

6.11 

Analogue output modules, electrically isolated

PCD2.W605

6 analogue outputs 10 bit resolution, 0..10 V

PCD2.W615

4 analogue outputs 10 bit resolution, 0..10 V

PCD2.W625

6 analogue outputs 10 bit resolution, 0..10 V

Galvanic separation of outputs to PCD, channels themselves not separated

I/O modules and I/O terminal blocks may only be plugged in and removed when the 

PCD and the ex24 V are disconnected from the power supply.

6.11.1  PCD2.W6x5, analogue outputs, electrically isolated, 6 (4) channels,

 

10 bit resolution 

Application

High-speed output module for general use, electrically isolated, 6 (4) channels, each 

with 10 bit resolution. Different variants for voltage 0..10 V, -10 V...+10 V and current 

0..20 mA are available.

Module overview

Channels

Resolution

PCD2.W605:

Voltage 0..10 V

6 (O0 … O5)

10 mV

PCD2.W615:

Current 0...20 mA

4 (O0 … O3)

20 μA

PCD2.W625:

Voltage -10..10 V

6 (O0 … O5)

20 mV

Technical data

Output ranges:

see module overview

Galvanic separation:

500 V, electrical isolation of outputs to PCD, 

channels themselves not separated

Resolution (digital representation): 10 bit (0 … 1023)

Load resistance:

W605:   

>3 kΩ

 

W615:   

<500 Ω*

 

W625:   

>3 kΩ

Accuracy at 25°C

W605:   

± 0.4 % 

W615:   

± 0.7 % 

W625:   

± 0.4 %

Temperature error (0 … 

+55 

°C)

± 0.25 %, 100 ppm/K or 0.01 %/K

Short circuit protection:

yes (permanent)

EMC protection:

acc. to standards ENV 50141, EN 55022, 

EN 61 000-4-2, EN 61 000-4-4, EN 61 000-4-5

Time constant of output filter:

W605:  

typ. 1 ms 

W615:  

typ. 0.3 ms 

W615:  

typ. 1 ms

Internal current consumption: 

(from +5 V bus)

W605:  

110 mA (typ. 80 mA)

 

W615:  

55 mA (typ. 45 mA)

 

W625:  

110 mA (typ. 80 mA)

Summary of Contents for PCD2.M5 Series





















































































































































































































































Reviews:

No comments