SB Filters AS-1005 Installation Instructions Download Page 1

WARNING!

(MUST READ PRIOR TO INSTALLATION)

II. Scoop Obstruction:

Regularly inspect the entire Scoop Inlet for any obstruction or debris that may impede the flow of air. 

III. Ride Height

Make sure there is plenty space between your tire and the scoop before driving.  The scoop system may not work with 
aftermarket wheels and tires.

IV.

 

Do NOT Seal Off Stock Inlet Location:

In addition to pulling air from the base of the air box, the S&B Cold Air Intake Kit pulls air from the same location as the 
stock induction system. 

UNDER NO CIRCUMSTANCE SHOULD YOU SEAL OFF THIS AIR INLET

. Doing so could 

result in severe injury or death or damage to the vehicle or property. Sealing off the stock air inlet could cause a 
significant vacuum should the Scoop become partially or completely obstructed which among other things could pull oil 
into intake tube leading to an explosion and/or a run-away truck condition as the oil would serve as fuel to the engine. 

15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 -

 

www.sbfilters.com

1

V.

 

Warranty for Scoop & Filter Wrap

S&B provides a limited warranty to guarantee the product is free of material and workmanship defects. Any product will be replaced upon 

identification of such defect.  Normal wear and tear is not covered under this warranty.  Final authorization is at the sole discretion of S&B 

Filters, Inc.

VI. How long will the Scoop & Filter Wraps Repel Water?

The Scoop & Filter Wraps are specially treated to repel water. The water repellency longevity is dependent upon driving conditions and the 

number of times the filter is cleaned.  Generally speaking, we recommend changing the Filter Wrap every 6-12 months.  However, a 

quick test can determine if it is time to change your Filter Wrap.  Simply take an ordinary clean spray bottle filled with water and gently 

spray the Filter Wrap.  If the water beads off the Filter Wrap, your water repellency is still working.  If you see water enter through the Filter 

Wrap, it is time to purchase a new Filter Wrap.

I. Water Ingestion Disclaimer:

This product is intended for general highway use only! Under normal driving conditions water ingestion is usually not an 
issue; however, if the product becomes submerged from rain or puddles due to harsh rains or flooding, the engine may 
ingest water which could cause severe engine damage. Do NOT use this product when crossing any body of water 
including but not limited to large puddles, streams, rivers or lakes. 

If your engine ingests water, this could cause severe engine damage by hydro-lock or other conditions. Care should be 
taken to avoid these driving conditions. 

ENGINE DAMAGE CAUSED BY THE INGESTION OF WATER INTO THE 

ENGINE IS THE DRIVER’S RESPONSIBILITY AND IS NOT COVERED BY S&B FILTERS! 

Summary of Contents for AS-1005

Page 1: ... covered under this warranty Final authorization is at the sole discretion of S B Filters Inc VI How long will the Scoop Filter Wraps Repel Water The Scoop Filter Wraps are specially treated to repel water The water repellency longevity is dependent upon driving conditions and the number of times the filter is cleaned Generally speaking we recommend changing the Filter Wrap every 6 12 months Howev...

Page 2: ...components listed on page 5 are present If you are missing any of the components call our customer support at 909 947 0015 Do not work on your vehicle while engine is hot Make sure the engine is turned off and the vehicle is in Park or the Parking Brake is set Thread Locker Use We have provided a small tube of thread locker in your kit This will keep your hardware from vibrating loose during rough...

Page 3: ...cause severe engine damage by hydro lock or other conditions Care should be taken to avoid these driving conditions ENGINE DAMAGE CAUSED BY THE INGESTION OF WATER INTO THE ENGINE IS THE DRIVER S RESPONSIBILITY AND IS NOT COVERED BY S B FILTERS 10 Attach the scoop channel to the air inlet tube using two 1 4 20x1 0 Hex Screws B and 1 4 Flat Washers C Tighten both using a 7 16 socket Testing and Main...

Page 4: ...ed P N AS 1005 4 ITEM QTY DESCRIPTION P N A 1 Cold Air Scoop AL1132 00 B 4 Screw Hex Cap 1 4 20x1 0 AL1131 00 C 6 Washer Flat 1 4 AI1073 00 D 2 Nut Clip 1 4 20 AL1059 00 E 2 Washer Split Lock 1 4 AI1309 00 F 1 Mounting Bracket AI1556 00 G 2 Nut Hex Nyloc 1 4 20 AI1074 00 AM0188 00 Rev A 11 20 12 Intake Kit Sold Separately ...

Reviews: