Savvier Fitness Booty Kicker BK2000 Use And Assembly Instructions Download Page 1

USE AND ASSEMBLY INSTRUCTIONS 

Congratulations on receipt of your Fitness Barre. The innovative patented design will provide you with great 

Barre fitness workouts that will kick your booty, tighten your abs and tone your entire body.

EASY VIDEO INSTRUCTIONS: 

www.BootyKicker.com/Instructions

A n   i n n o v a t i o n   p o w e r e d   b y   S a v v i e r   F i t n e s s ®

Copyright 2019-2021 Savvier Fitness® LLC

BK2000 (201223)

CAUTION! READ ALL INFORMATION BEFORE USE.
SERIOUS INJURY OR FATALITY MAY OCCUR

• 

The Booty Kicker® is not a toy. Keep out of reach of children.

• 

Always check with your physician before starting this or any exercise program.

• 

Do not use the Booty Kicker® for anything other than its intended exercise purpose. Use only as shown, illustrated and 

intended.

• 

Do not attempt any type of gymnastic movements on the Booty Kicker®.

• 

Always inspect the Booty Kicker® before every use for loose screws, nuts or damage. Tighten any screws or nuts prior to 

use. If you find any cracks or damage, then discontinue use immediately.

• 

Only use the Booty Kicker® on a clean level surface making sure you have adequate clearance around the Booty Kicker® 

for performing the exercises.

• 

When using the Booty Kicker®, only engage your hands, arms, legs, or feet with the wooden barre. The metal uprights and 

base legs are not intended to be used as gripping or exercise surfaces.

• 

Similarly, when using any type of resistance band with the Booty Kicker®, engage the band only with the wooden barre. Do 

not allow bands to contact sharp objects. Be sure to inspect any resistance bands before use and discontinue use if any 

signs of nicks or tears.

• 

When first attempting any exercise, use caution while determining your physical limitations. When performing any exercise 

involving pushing or pulling forces on the barre, use caution to assure such forces do not create an instability causing 

either you or the barre to tip over. Placing hands (or in the case of a resistance band) towards the middle of the wooden 

barre increases stability.

• 

Placing weights in the weight racks increases the Booty Kicker® stability for performing certain pushing/pulling exercises. 

Removing weights during exercises reduces the unit stability.

• 

Be sure to wear appropriate exercise clothing.

• 

Always properly store the Booty Kicker® indoors after use. The Booty Kicker® could pose a hazard to children and pets, 

and should not be left unattended. Store out of reach of children when not in use.

• 

Use caution when folding, as hinges may pose pinch points for fingers, hands, feet and toes. When the Booty Kicker® is in 

the folded position, always secure base legs and uprights together with the two Velcro straps. Weights should be removed 

from weight racks when moving / transporting the Booty Kicker®.

Summary of Contents for Booty Kicker BK2000

Page 1: ...base legs are not intended to be used as gripping or exercise surfaces Similarly when using any type of resistance band with the Booty Kicker engage the band only with the wooden barre Do not allow bands to contact sharp objects Be sure to inspect any resistance bands before use and discontinue use if any signs of nicks or tears When first attempting any exercise use caution while determining your...

Page 2: ...nd in the video Assemble on a flat level hard floor not carpet or rug DO NOT fully tighten nuts and screws until the unit is fully assembled Only finger tighten hex nuts and keep screws loose Tighten with tools only in Step 4 Carefully unpack and familiarize yourself with each component assembly hardware and tools Remove the Base Rod and two Cross Rods shipped inside the Upright Bar and the Leg As...

Page 3: ...hole As shown in Fig 2 Repeat on the other side of the assembly Place the Straps onto the Gusset Rods While holding the unit in place gently pull outward on a Gusset Rod and rotate to place the first hole of the Strap onto the Gusset Rod Important Assemble the Strap with the hook or scratchy side of the Velcro facing upward As shown in Fig 2 Do not wrap the Strap yet Step 3 Place the Brackets in t...

Page 4: ...t Acorn Nuts Confirm unit is sitting flat and if needed repeat the loosen adjustment tighten process Place the Stretch Sleeve onto the Full Assembly one side at a time Align the Sleeve between the Cross Bar Acorn Nuts with the seam of the Sleeve between the Cross Bar Acorn Nuts and the seam of the Sleeve at the Upright Bar As shown in Fig 5 Step 5 Weight Racks Assemble the optional identical Weigh...

Reviews: