The SmartControl 8 with PoE (SSC-P008) Quick Reference Guide provides information
necessary to install the SSC-P008, a solution for small business installations or system
expansions. The SSC-P008 supports Power over Ethernet using the IEEE 802.3af standard.
Box Contents
(1) SmartControl 8 (SSC-P008)
(1) SSC-P008 Installation Kit (075-0124-xx)
•
(2) 6-Pin Screw-Down Connector (028-9352-xx)
•
(8) Screws #6 x 1/4 Phillips (039-0143-xx)
•
(2) Side mount brackets (071-0625-xx)
(1) Quick Reference Guide (this document)
Optional Accessories
Power Supply 5V DC 2.5 Amps (PWR-5025)
RS-232 Adapters (SAK-1000)
Infrared (IR) Emitters (IRB-1000)
Specifications
Environmental
Environmental
Temperature
32° to 104° F (0° to 40° C)
Humidity
10% to 90% Relative Humidity (non-condensing)
Cooling
1 cubic feet per minute (CFM) recommended
Maximum BTUs
17 BTUs per hour
Dimensions and Weight
Dimensions and Weight
Height
1.59 in/4.04 cm
Width
4.31 in/10.96 cm
Depth
6.50 in/16.51 cm
Weight
3.00 lb/1.36 kg (shipping weight)
PoE Power
PoE Power
PoE
RJ-45 10/100 Base-T, Power over Ethernet using the PoE
IEEE 802.3af standard.
Nominal Power
3 watts at 5V DC
Maximum Power
5 watts at 5V DC
Optional Power Supply
Optional Power Supply
Input Power
5V DC, 120-240V AC, 50/60 Hz
Nominal Power
1.3 watts at 5V DC
Nominal Power
1.6 watts at 120V AC
Maximum Power
2 watts at 5V DC
Maximum Power
3 watts at 120V AC
Compliance
Compliance
Safety and Emissions
FCC Part 15 | CE Mark | C-Tick
RoHS
Compliant
Front View of SSC-P008
The next table describes the SSC-P008 LEDs
IR LED
Green
indicates IR port signal activity.
Off
indicates no IR port activity.
Ground Connector (Optional)
Connect this terminal to a suitable ground surface.
CPU Status LED
Green
indicates the Host has established communications
with the SSC-P008.
Green flashing
indicates the SSC-P008 is ready (running with
DHCP IP address), but the Host has not established
communications with the SSC-P008.
Off
indicates the SSC-P008 is resetting or is booting the
embedded firmware.
Red
indicates the Host has determined the firmware needs to
be updated, but a problem occurred during the process that
will initiate a reset.
Red flashing
indicates the firmware is running, but has not
received a DHCP IP Address.
Amber
indicates the Host is currently updating the firmware.
Amber flashing
indicates the SSC-P008 has a valid link-local
IP Address and is waiting to connect to the Host.
1
6
7
2
3
4
5
8
Rear View of SSC-P008
The next table describes the functionality on the rear of an SSC-P008.
1
Reset button
Resets the factory default DHCP mode.
Press and hold the reset button for 5+ seconds.
2
Link LED
Green
indicates an Ethernet link has been established.
Green flashing
indicates Ethernet activity.
Off
indicates an Ethernet link has not been established.
3
Activity LED
Green
indicates an Ethernet speed of 100 Mb.
Off
indicates an Ethernet speed of 10 Mb
4
RS232/485-1
8-pin RJ-45 female: Used to transmit and receive serial
binary data to and from devices. Supports RS-232/422.
5
IR (1-6 ports)
6-Pin Screw Down Plug in Connector: (5V tolerant only)
Sends IR signals to control devices with an IR input or IR
receiver via an IR flasher.
See IR Wiring for important precautions regarding IR
functionality before making any connections.
6
Ethernet
RJ-45 10/100 Base-T, auto-negotiating port.
Supports Power over Ethernet using the PoE IEEE
802.3af standard.
7
RS232/485-2
8-pin RJ-45 female: Used to transmit and receive serial
binary data to and from devices. Supports RS-232/422.
8
5V DC power
connector
(Optional)
5V DC input power to the SSC-P008.
NOTE
: All components requiring 120-240V AC, 50/60 Hz source power must be connected to a
surge-protected circuit.
SmartControl 8 (PoE)
(SSC-P008)
Quick Reference Guide
009-0807-03
SSC-P008-00
140827
