In-Wall Wired Charging & Control Dock
(ICC-T000)
Quick Reference Guide
009-0427-01
ICC-T000-xx
Copyright © 2012 Savant Systems LLC, SAVANT and RacePoint Blueprint are trademarks of Savant Systems, LLC.
Apple®, iTunes®, iPad, iPad2, iPod touch®, iPod® Classic and iPod nano® are registered trademarks or trade names of Apple Inc.
All brand names, product names and trademarks are the property of their respective owners.
Savant Systems, LLC reserves the right to change product specifications without notice.
Savant Confidential and Proprietary
031512
45 Perseverance Way, Hyannis, MA 02601 Phone 508.683.2500 Fax 508.683.2600 SavantSystems.com
The Savant
®
In-Wall Wired Charging & Control Dock (ICC-T000) Quick Reference Guide
provides the information necessary to install the In-Wall Wired Charging & Control Dock for
Apple iOS devices.
Box Contents
(1) In-Wall Wired Charging & Control Dock (ICC-T000)
(1) Cut out template (009-0245-xx)
(1) Installation Kit (075-0106-xx)
•
(1) 24V DC 60W power supply (025-0046-xx)
•
(1) Power Cable (2 ft) (064-0048-xx) or appropriate international cord
•
(4) #6 x 1.5 Screw (039-0173-xx)
•
(4) #6-32 x 2.25 Screw (039-0209-xx)
•
(2) 2-position, Phoenix Connector (028-9160-xx)
(1) Quick Reference Guide (this document)
Accessories
(1) In-Wall Bezel for iPod 1-Pack (BZB/W/A/P-1iPod-xx) Black/White/Almond/Primer
(1) In-Wall Bezel for iPod 5-Pack (BZB/W/A/P-5iPod-xx) Black/White/Almond/Primer
(Single color per 5-Pack)
(1) Construction Box for In-Wall Dock (RIB-IT00)
Specifications
Environmental
Operating Temperature
32º to 104º F (0º to 40º C)
Operating Humidity
10% to 90% Non-condensing
In-Wall Dock - Dimensions and Weight
Dimensions (H x W x D)
6.3 in x 3.6 in x 2.5 in (16.3 cm x 9.1 cm x 6.4 cm)
Weight
1.0 lb/0.45 kg
In-Wall Dock Bezel - Dimensions and Weight
Dimensions (H x W x D)
*
6.4 in x 3.7 in x 0.14 in (16.3 cm x 9.4 cm x 0.35 cm)
Weight
0.25 lb/0.11 kg
Power
Supply
24V DC, 120-230V AC, 50/60Hz
Maximum Power Draw
10 Watts
Power cable length5
300 ft maximum AWG 20
Compliance
Safety and Emissions
FCC Part 15/CE Mark/C-Tick
RoHS
Compliant
SURGE PROTECTION
: Use a surge-protected circuit for all components requiring
120/230V AC, 50/60 Hz source power.
ELECTRICAL DISCONNECT
: The 120/230V AC, 50/60 Hz source power outlet and
input power sockets should be easily accessible in the event of an electrical hazard or
malfunction condition.
ELECTRICAL DISCONNECT
: Remove power before working on the dock.
Wiring to Dock
Wiring and Pinouts
In-Wall Wired Charging Dock 24V DC
+ (
Positive)
White
24V DC In
-
(Negative)
Black
24V DC Return
Installation without RIB-IT00 Construction Box
Note
: The iPod dock can be installed in either landscape or portrait orientation.
1.
Connect the 24V DC power supply to the In-Wall Dock and route inside the wall
opening.
2.
Route the Cat5 cable to inside the wall opening.
3.
After making the connections to
In-Wall Dock, position the unit in the opening and
secure with the four rotating mounting tabs.
4.
Turn the tab screws clockwise; the tabs will grab the interior wall. Tighten until snug.
Do not over tighten
.
Caution
: Do not use a powered screwdriver to tighten the tabs; the tabs can be easily over
tightened.
5.
Position the bezel over the In-Wall Dock and press, ensuring that the wall plate seats
properly. (See below)
6.
Configure the installation using RacePoint Blueprint
™
.
Note
: The In-Wall Dock also has optional screw mounting holes for optional stud mounting.
Optional Pre/Post-Construction Box
Note
: The In-Wall Dock Assembly is not a weather resistant unit. Do not locate in a damp or
humid area.
The ICC-T000 can be installed with or without an in-wall construction box. The in-wall
construction box (RIB-IT00) is optional and can be used pre-or post-construction to save the
space required for the ICC-T000, ICC-TP00 or IDC-T000 and to terminate the roughed in
wires.
Important
: Always locate the studs and utilities (electrical wires, ducts, water and gas
pipes) before cutting an opening in the wall. Ensure all required power and control cables
have been routed to the site of construction box.
Installing the In-Wall Dock into the RIB-IT00
1.
Remove Retainer caps (4) from the back of the ICC-T000 with pliers.
2.
Remove tabs (4) by removing the screws.
3.
Place the ICC-T000 into the RIB-IT00 and use the 8-32 screws (4) to attach.
Caution
: Do not use a powered screwdriver to tighten the tabs; the tabs can be easily over
tightened.