sauter Equitherm EQJW 125 User Manual Download Page 59 | Manualshive

Page: 59 / 74

background image

EQJW 125: Heating controller

Resistance values for the Ni1000 sensors

58

7001029003 A

© Fr. Sauter AG

10

Resistance values for the Ni1000 sensors

The temperature sensors required depending on the use of the EQJW 125
must conform to DIN 43760.

Temperature (°C)

Resistance value ( ) Ni1000

90

1549

80

1483

70

1417

60

1353

50

1291

40

1230

30

1171

20

1112

10

1056

0

1000

–10

946

–20

893

–30

842

–40

791

Tab. 8: Resistance value Ni1000

The resistance value of the nickel measuring resistor changes in relation to
the temperature. The temperature coefficient is always positive, i.e. the
resistance increases as the temperature rises. See the table of values
(DIN 43760). Within the specified tolerances, the sensors can be exchanged
without calibration.

«
...
57
58
59
60
61
...
»

Summary of Contents for Equitherm EQJW 125











































































Reviews:

No comments

Related manuals for Equitherm EQJW 125

Brand: QCON Pages: 4

Brand: ZKTeco Pages: 20

Brand: ZKTeco Pages: 8

Brand: ZKTeco Pages: 10

Brand: ZKTeco Pages: 121

Brand: ZKTeco Pages: 12

Brand: ZKTeco Pages: 6

Brand: ZiLOG Pages: 12

Brand: Paradox Pages: 3

Brand: µ-Dimension Pages: 48

Brand: µ-Dimension Pages: 2

CWDM-CR-B Series

Brand: Lantronix Pages: 19

Brand: Netafim Pages: 4

Brand: TREND Pages: 12

Brand: Kunert Professional Pages: 29

Brand: GSD Pages: 5

Brand: Bardiani Valvole Pages: 24

Brand: Atmel Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands