Saturn 2003 Ion Page 67 Service Manual Supplement Download

Page: 67 / 186

7. Remove the front suspension support.

Installation Procedure

Important: If the location of the original plug weld
holes can not be determined, space the plug
weld holes every 40 mm (1

⁄

in) apart.

1. Drill 8 mm (5/16 in) plug weld holes in the service

part as necessary in the locations noted from the
original panel.

2. Prepare all mating surfaces as necessary.

3. Apply 3M Weld-Thru Coating P/N 05916 or

equivalent to all mating surfaces.

4. Position the front suspension support to the

vehicle using 3–dimensional measuring
equipment. Clamp the support into place.

867629

865265

867629

2003 Saturn Ion

3-67

2003

Saturn

Ion

Summary of Contents for 2003 Ion



























































































































































































Search results

Summary of Contents for 2003 Ion

Reviews:

Related manuals for 2003 Ion

Brands by name

Popular brands

Saturn 2003 Ion, Service Manual Supplement

Search results

Summary of Contents for 2003 Ion

Reviews:

Related manuals for 2003 Ion

Brands by name

Popular brands