manualshive.com logo in svg

Saturn 2003 Ion, Service Manual Supplement, Page: 183 / 186

Share
Download
Saturn 2003 Ion Service Manual Supplement Download Page 183

9. Remove the passenger/right outer trim cover from

the I/P (3).

10. Remove the CPA from the I/P module yellow

connector (1).

11. Disconnect the I/P module yellow connector (1)

from the vehicle harness yellow connector (2).

12. Remove the lower right center pillar.

13. Remove the connector position assurance (CPA)

from pretensioner connector.

14. Disconnect the right/passenger pretensioner

connector from the vehicle harness yellow
connector.

15. Remove the driver/left outer trim cover from the

instrument panel (I/P).

16. Remove the CPA from the steering wheel module

coil yellow connector.

17. Disconnect the steering wheel module coil yellow

connector from the vehicle harness yellow
connector.

18. Remove the lower left center pillar.

816857

899818

877766

2003 Saturn Ion

3-183

2003

Saturn

Ion

Summary of Contents for 2003 Ion



























































































































































































Reviews:

No comments