manualshive.com logo in svg

SATO SG112 ex, Programming Reference Manual

Share
Download
SATO SG112 ex Programming Reference Manual Download Page 498

497

SNTP (Simple Network Time Protocol)

SNTP corrects time of calendar IC when calendar IC is equipped.
Note that Wireless LAN is not supported.

Function

This function acquires the current time from the NTP server and corrects time of the calender IC

at the printer power on when a calender IC is mounted on the printer and LAN is selected as [data

port] at the [communication setting]. ENABLE/DISABLE the SNTP and IP address setting of the NTP

server can be done on the communication setting mode.
This function is available only when a calender IC is mounted to the printer.

Operating Conditions

The operating conditions of the SNTP function are as follows.

-

A calender IC is mounted to the printer.

-

Communication setting is LAN.
Select LAN at the [communication setting] - [data port].

-

Available only in the Normal mode.

Summary of Contents for SG112 ex





































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands