SATO SG112 ex Programming Reference Manual Download Page 302

Page: 302 / 516

301

System Commands

[ESC+CS] Print Speed

ESC

Parameter

Hexadecimal code

<1B>

<43>

<53>

Initial value

Refer to [Parameter Initial Value and Specified Range] section below.

When the power is OFF

The set parameter is maintained.

Valid range within items

The set parameter is valid until the next specification is

made.

Valid range and term of

command

Valid range between items

The set parameter is valid until the next specification is

made.

[Function]

Specifying the speed of printing.

[Format]

<CS>aa

Parameter

a [Print speed] = Refer to [Initial value for parameter and Valid range] section below.

[Coding Example]

<A>

<CS>4

<Z>

[Supplementary Explanation]

Print speed value specified by the command or "Settings" mode is maintained.

[Points]

If the value over valid range is specified, command error will occur and print speed will not be

changed.

Use default set operation of printer to set back the value to the initial one.

Summary of Contents for SG112 ex





































































































































































































































































































































































































































































































































Search results

Summary of Contents for SG112 ex

Reviews:

Brands by name

Popular brands

SATO SG112 ex, Programming Reference Manual

Search results

Summary of Contents for SG112 ex

Reviews:

Brands by name

Popular brands