Satel SENNET DL150 Manual Download | Manualshive

Page: 63 / 87

background image

S

E

TTING

Manual Datalogger SenNet DL150 / DL151 / DL170 / DL171 / DL172

Versión 1.01

Satel Spain

63

Figure 36. Example of connection of a generic device using Modbus RTU or Modbus TCP

15.2.2.

Connecting a KNX device

Not all devices with KNX protocol are implemented to be directly connected to the datalogger. Ask
your SenNet supplier or contact Satel Spain if you need to connect to any particular device.

To connect a KNX device, first select the box

KNX

from

Configuration

>

Application parameters

, so the

datalogger can start seeking the KNX network.

Then, add the device to the table

List of devices

:

▪

Type of

device:

select the type of KNX device. If your device was not in the list, it will be

necessary to implement

it

.

▪

Comm id

: address of the device within the KNX installation.

▪

App id

: the sending ID (the ID to send the data to the platform). In general, subsequent

numbers are used (1, 2, 3

…

n) according to the order of the devices in the table.

▪

Communication params

: in this case this field must be left empty because the datalogger can

communicate with the KNX network only through a KNX router that converts the KNX signals
into RS232. This connection is internally configured in the application.

▪

Name

: the name you wish to assign to the device.

▪

Additional param

: addresses where the devices host the data to be read. They depend on the

device and the configuration of the KNX installation.

▪

Box:

Able

. To enable the device.

Figure 37. Example of connection of three KNX devices

15.2.3.

Connecting a Z-Wave device

For connecting a device with Z-Wave, your datalogger must have the Z-Wave radio model installed.
For more details, please check the chapter on Z-Wave (p. 132

et seq

).

The datalogger can read the data sent by the Z-Wave-devices only if they are already added to the Z-
Wave network. This must be done at the standard Z-Wave platform.

Then you have to access to the

visualization mode

to get the device code. This code is required to configure the device in the

datalogger's interface.

«
...
61
62
63
64
65
...
»

Summary of Contents for SENNET DL150
























































































Reviews:

No comments

Related manuals for SENNET DL150

Brand: Metal Samples Company Pages: 54

Brand: ICP DAS USA Pages: 131

Brand: Aim Pages: 11

Brand: Vista Pages: 3

Brand: Chauvin Arnoux Pages: 36

Brand: GRAPHTEC Pages: 158

Brand: Ebro Pages: 24

Brand: Omega Engineering Pages: 6

Brand: TESTO Pages: 2

Brand: TESTO Pages: 8

Brand: TESTO Pages: 32

Synergy Compact

Brand: Tidal Engineering Pages: 346

Brand: ELPRO Pages: 28

Brand: Relay Pages: 8

Brand: Relay Pages: 20

Brand: Neuralynx Pages: 38

Brand: mIoT Pages: 10

Brand: mIoT Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands