Satec ezPAC SA300 Series Installation Manual Download Page 36

Page: 36 / 43

Appendix: Technical Specifications

Appendix: Technical Specifications

Environmental Conditions

Operating Temperature: -20°C to 60°C (-4°F to 140°F)

Storage Temperature: -25°C to 80°C (-13°F to 176°F)

Humidity: 0 to 95% non-condensing

Construction

Overall Dimensions

Length: 284.00 mm (11.181 Inches)

Width: 255.24 mm (10.05 Inches)

Depth: 185.00 mm (7.28 Inches)

Weight: 5.0kg (11.02 Lb)

Materials

Enclosure: Cold rolled Steel

Panels I/O: Aluminum

Face Plates with Graphics: Polycarbonate film

PCB. : FR4 (UL94-V0)

Terminals: PBT (UL94-V0)

Connectors-Plug-in type: Polyamide PA6.6 (UL94-V0)

Packaging Case: Carton and Stratocell (Polyethylene Foam) Brackets

Labels: Polyester film (UL94-V0)

Power Supply

Isolation: galvanically isolated

Option 120/230 VAC-110/220 VDC: Rated input 85-265VAC 50/60 Hz, 88-290VDC, Burden 20W

12 VDC Option: Rated input 9.6-19 VDC

24 VDC Option: Rated input 19-37 VDC

48 VDC Option: Rated input 37- 72 VDC

Input Ratings

AC Voltage Inputs: V1, V2, V3, VN

Operating Range: 690VAC line-to-line, 400VAC line-to-neutral

Direct input and input via PT (up to 828VAC line-to-line, up to 480VAC line-to-neutral)

Input Impedance: 500 kOhm

Burden for 400V: < 0.35 VA

Burden for 120V: < 0.03 VA

Overvoltage Withstand: 1000VAC continuous, 2500VAC for 1 second

Galvanic Isolation: 3500V AC

Wire Size: up to 10 AWG (up to 6 mm

)

Terminals Pitch 9.5 mm

AC Voltage Inputs: V4, V4N

Operating Range: 400VAC

Direct input and input via PT (up to 480VAC)

Input Impedance: 500 kOhm

Burden for 400V: < 0.35 VA

Burden for 120V: < 0.03 VA

Overvoltage Withstand: 1000VAC continuous, 2500VAC for 1 second

Galvanic Isolation: 3500V AC

Wire Size: 10 AWG ( up to 6 mm

)

Summary of Contents for ezPAC SA300 Series












































Search results

Summary of Contents for ezPAC SA300 Series

Reviews:

Brands by name

Popular brands

Satec ezPAC SA300 Series, Installation Manual

Search results

Summary of Contents for ezPAC SA300 Series

Reviews:

Brands by name

Popular brands