background image

20

Disposal

Information on Decontamination

The device does not contain any hazard-

ous materials that would necessitate spe-

cial disposal actions�

Contaminated samples used during the 

process are potentially hazardous materi-

als that could cause biological or chemi-

cal hazards�

If the device has come into contact with 

hazardous substances: Steps must be 

taken to ensure proper decontamination 

and declaration� The operator is responsi-

ble for adhering to local government reg-

ulations on the proper declaration of 

transport and disposal and the proper 

disposal of the device�

!

 

Warning

  Risk of injury due to contaminated 

devices!

  Devices contaminated with hazardous 

materials (NBC contamination) will not be 

accepted by Sartorius for repair or disposal�

Dispose of Device and Parts
Information on Disposal

The device and the device accessories 

must be disposed of properly by disposal 

facilities�

A lithium cell battery, type CR2032, is 

installed inside the device� Batteries must 

be disposed of properly by disposal facili-

ties�

The packaging is made of environmental-

ly friendly materials that can be used as 

secondary raw materials�

Disposal
Requirements

The device has been decontaminated�

Procedure

–  Dispose of the device� Follow the disposal 

instructions on our website 

(www�sartorius�com)�

–  Dispose of the packaging in accordance 

with local government regulations�

Summary of Contents for PMA.Power

































Reviews: