manualshive.com logo in svg

Sartorius BioPAT Xgas Vis, Operating Manual

Share
Download
Sartorius BioPAT Xgas Vis Operating Manual Download Page 19

 

Operating Manual BioPAT

®

 Xgas Vis 

19

 

 

Software Installation 

 

 

Software Installation 

5.2  BioPAT

®

 Xgas Vis Software

This chapter describes the installation of the BioPAT

®

 Xgas Vis Software. 

NOTE 

Please consider that MFCS/win must have been already installed.
Please note, the installation of this software requires local administrative 
rights.

The CD-ROM containing the BioPAT

®

 Xgas Vis Software is labeled as 

“BioPAT

®

 Xgas Vis Soft ware”. A separate program named SETUP.EXE 

performs the software installation. 
The following steps describe the installation on your computer system.

Installing the BioPAT

®

 Xgas Vis Software

 

t

Shutdown the MFCS/win system from the MFCS/win Shell.

 

t

Insert the CD-ROM into the CD drive.

 

t

Open the windows explorer and change to the CD drive.

 

t

Double-click on file SETUP.EXE to start the installation program.

 

t

If the “.Net Framework 3.5” is not installed, then the following dialog 
will be shown on the screen.

Summary of Contents for BioPAT Xgas Vis
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands