Sanyo XS1271 Instruction Manual Download Page 15

15

TROUBLESHOOTING

If your air conditioner does not work properly, first check the following 
points before requesting service. If it still does not work properly, 
contact your dealer or service center.

OPERATING RANGE

The air conditioner is operable within the temperature ranges as 
listed below:
For Cooling Only Models : C1271, C1872 

For Low Ambient Cooling Models : CL1271, CL1872 

WIRED REMOTE CONTROLLER

A separately sold wired remote controller (STK-RCS-
7TWSU) used with this air conditioner is also available. If 
you wish to use the wired remote control function, you will 
need to purchase the optional wired remote controller.

Trouble Possible 

Cause Remedy

Air conditioner does 
not run at all.

1. Power failure. 

1. Restore power.

2. Leakage circuit 

breaker tripped.

2. Contact service 

center.

3. Line voltage is too 

low.

3. Consult your 

electrician or 
dealer.

4. Batteries in remote 

control unit have 
run down.

4. Replace batteries.

OPERATION lamp 
blinks and air 
conditioner does not 
operate.

Trouble in system.

Contact service 
center.

Compressor runs but 
soon stops.

Obstruction in front of 
condenser coil.

Remove obstruction.

Poor cooling 
performance.

1. Dirty or clogged air 

filter.

1. Clean air filter to 

improve airflow.

2. Heat source or 

many people in 
room.

2. Eliminate heat 

source if possible.

3. Doors and/or 

windows are open.

3. Shut them to keep 

the heat out.

4. Obstacle near air 

intake or air 
discharge port.

4. Remove it to ensure 

good airflow.

5. Thermostat is set 

too high for cooling.

5. Set the temperature 

lower.

Clicking sound is 
heard from the air 
conditioner.

In cooling operation, 
any plastic parts may 
shrink due to a 
sudden temperature 
change. In this event, 
a clicking sound may 
occur.

This is normal, and 
the sound will soon 
disappear.

OPERATION lamp 
lights but outdoor unit 
will not run.

The use of cellular 
phones near the air 
conditioner may cause 
disturbance to its 
normal operation.

1. Turn off the power 

then restart the air 
conditioner after a 
while.

2. Consult your dealer.

TIMER lamp blinks 
(3 sec. interval) and 
air conditioner does 
not operate.

FLOAT SWITCH is 
actived.

Contact service 
center.

Temperature Indoor 

air 

temperature 

Outdoor air 
temperature

COOLING

Max. 

95 °F DB / 
71 °F WB 

115 °F DB

Min. 

67 °F DB / 
57 °F WB 

67 °F DB

Temperature Indoor 

air 

temperature 

Outdoor air 
temperature

COOLING

Max. 

95 °F DB / 
71 °F WB 

115 °F DB

Min. 

67 °F DB / 
57 °F WB 

0 °F DB

OI-108-15-EG

01_XS1872_EN.fm  Page 15  Thursday, September 25, 2008  8:31 PM

Summary of Contents for XS1271























Reviews: