background image

SERVICE MANUAL

Digital Camera

VPC-A5

VPC-A5EX

(Product Code : 126 694 00)
(Korea)
(Taiwan)

(Product Code : 126 694 01)
(Europe)
(Asia)

Contents

1. OUTLINE OF CIRCUIT DESCRIPTION .................... 2
2. DISASSEMBLY ........................................................ 10
3. ELECTRICAL ADJUSTMENT .................................. 14
4. USB STORAGE INFORMATION
    REGISTRATION ...................................................... 19
5. TROUBLESHOOTING GUIDE ................................. 20
6. PARTS LIST ............................................................. 22
    CABINET AND CHASSIS PARTS 1 ........................ 22
    CABINET AND CHASSIS PARTS 2 ........................ 24
    ELECTRICAL PARTS .............................................. 26
    PACKING MATERIALS ............................................ 30
    ACCESSORIES ....................................................... 30
CIRCUIT DIAGRAMS &
PRINTED WIRING BOARDS ...................................... C1

The components designated by a symbol (   !   ) in this schematic diagram designates components whose value are of

special significance to product safety. Should any component designated by a symbol need to be replaced, use only the part

designated in the Parts List. Do not deviate from the resistance, wattage, and voltage ratings shown.

CAUTION : Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.

NOTE : 1. Parts order must contain model number, part number, and description.

2. Substitute parts may be supplied as the service parts.
3. N. S. P. : Not available as service parts.

Design and specification are subject to change without notice.

SX71A/U, EX

REFERENCE No. SM5310603

FILE NO.

PRODUCT SAFETY NOTICE

Summary of Contents for Xacti VPC-A5

































Reviews: