background image

Parts supplied with remote controller

See Table 1.

Remote controller installation guidelines

• Mount the remote controller 1 to 1.5 meters off the

floor where it can sense the average temperature of
the room.

• Do not mount the remote controller in a place

exposed to direct sunlight or where it is exposed to
outside air such as near a window.

• Do not mount the remote controller behind a curtain

or other object so that it is separated from the air cir-
culation of the room.

• Mount the remote controller inside the room being air

conditioned.

• The remote controller should be mounted on a wall or

other surface vertically.

Room temperature sensors are separately incorporated
in both the indoor unit and the remote controller. Either
sensor can be used to sense the room temperature. The
indoor unit sensor is usually used.
If you wish the remote controller to sense the room tem-
perature, press the SENSOR button with a ballpoint pen
or tool with a small tip.

How to install the remote controller

<NOTE 1>

Do not twist the remote controller wire
with the power cord, or run them in the
same metal conduit, because this may
cause a malfunction.

<NOTE 2>

Install the remote controller away from all
sources of electrical noise.

<NOTE 3>

Install a noise filter or take other appro-
priate action if electrical noise affects the
power supply circuit of the unit.

• Use an electric junction box (supplied locally) for

embedded mounting of the remote controller. 
(See Fig. 1)

Switching the room temperature sensor

Installation location

Q’ty

No.

1

Supplied parts

Remote
controller

(comes with
200mm wire)

Machine screws
M4 

×

 25

Tapping screws
M4 

×

 25

2

2

Q’ty

No.

2

Supplied parts

Spacers

Wire joints

Harness

Clamper

Instruction manual

6

1

1

1

Table 1

85464359404000   © SANYO 2003

Note: Remote controller model name RCS-KS2432AWD

Code: 851-0-0054-590-00-0

W

INSTALLATION  INSTRUCTIONS

Fig. 1

Wall

Under-case (back case)

Electric junction box
(no cover)

Spacers

Remote controller

Lead wires (3)

Machine screws
M4 

×

 25 (2)

RCS-KS2432AWD

03-242.Sanyo.85464359404000  8/21/03  9:17 AM  Page 1

Summary of Contents for RCS-KS2432AWD

Page 1: ...llpoint pen or tool with a small tip How to install the remote controller NOTE 1 Do not twist the remote controller wire with the power cord or run them in the same metal conduit because this may cause a malfunction NOTE 2 Install the remote controller away from all sources of electrical noise NOTE 3 Install a noise filter or take other appro priate action if electrical noise affects the power sup...

Page 2: ...nit controller PCB ass y Fig 6 on next page 4 Pull out the lead wire that connects the remote con trol receiver to CN11 of the controller PCB ass y Fig 5 on next page 5 Plug the socket of the supplied wire harness onto CN11 6 Bind the wire harness and the inter unit lead wires together and route them Fasten them under the electrical box with the clamp Then pull them out from the back of the indoor...

Page 3: ... ORG YEL BLK FAN MOTOR P S G G G w FM HH H M L LL w w w w w w POWER TRANSFORMER TR1 IND LAMP ASSY RC1 CAPACITOR 1 2 G 4 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 FLP CONNECTOR WHT CONNECTOR WHT WHT WHT FLAP MOTOR UPPER CONTROLLER FLAP MOTOR LOWER ROOM THERMISTOR TH2 COIL THERMISTOR TH1 WHT BLU BLU BLU BLU 8512 5253 714XX 1 KS2432A Electric Wiring Diagram Fig 6 TRANS 1 2 G 4 C B P Controller PCB ass ...

Page 4: ...e system shifts into cooling oper ation and cool air will start to be felt Cooling oper ation with the switch at the TEST position is unaf fected by the room temperature 5 After stopping the test run turn the operation selec tor switch of the indoor unit to the OFF position once then move to ON position Fig 7 6 Press the ON OFF button on the remote control unit to stop the air conditioner If the u...

Reviews: