Sanyo PLC-WXE46, Service Manual

Page: 44 / 108

-44-
Group/
Item
Item Name Function Initial Range Note
1 Loop Count
Maximum Execution Times
(OFFSET->GAIN)
10 1 - 30
Auto Status
Result of Auto-Calibration (Last
Memory)
0 0 / 1 / 9
0: OK, 1: Adjusting,9: Error *
ReadOnly
3 AutoWait Wait Value for each setting 1 1 - 0
4 CHECK -Tolelance Torelance of OFFSET 1 - 55
Group
261
Auto Calibration (RGB)
0 OFFSET AREA H START
Black Level Acquiring Area H-Start
Position
975 0 - 1000
1 OFFSET AREA V START
Black Level Acquiring Area V-Start
Position
500 0 - 1000
GAIN AREA H START
White Level Acquiring Area H-Start
Position
5 0 - 1000
3 GAIN AREA V START
White Level Acquiring Area V-Start
Position
500 0 - 1000
4 Image AREA H WIDTH Black/White Level Acquiring Area 13 0 - 4095
5 Image AREA V HIGHT
Black/White Level Acquiring Area
Height
9 0 - 4095
6 OFFSET target Target Value of Black Level Adj. 3 0 - 17
7 OFFSET torelance Torelance of Black Level Adj. 1 1 - 17
8 GAIN target Target Value of White Level Adj. 38 0 - 55
9 GAIN torelance Torelance of White Level Adj. 1 1 - 55
Group
262
Auto Calibration (CVBS/SVIdEo)
0 Y Image Area Start X Y Acquiring Area H-Start Position 0 0 - 1000
1 Y Image Area Start Y Y Acquiring Area V-Start Position 500 0 - 1000
6 Image Area H Width Image Level Acquiring Area 13 0 - 4095
7 Image Area V Hight Image Level Acquiring Area Height 0 0 - 4095
8 Y Target Level Target Value of Y Level Adj. 17 0 - 55
11 Gain Tolerance Torelance of Level Adj. 1 0 - 55
1 Delta Gain Deviation Width of Gain Value 9 0 - 55
Group
264
Auto Calibration (YCbCr)
0 Y-OFFSET AREA H START
Y - Offset Acquiring Area H-Start
Position
95 0 - 1000
1 Y-OFFSET AREA V START
Y - Offset Acquiring Area V-Start
Position
500 0 - 1000
CB - OFFSET AREA H
START
CB - Offset Acquiring Area H-Start
Position
95 0 - 1000 If not used: use Y's value
3 CB - OFFSET AREA V
START
CB - Offset Acquiring Area V-Start
Position
500 0 - 1000 If not used: use Y's value
4 CR - OFFSET AREA H
START
CR - Offset Acquiring Area H-Start
Position
95 0 - 1000 If not used: use Y's value
5 CR - OFFSET AREA V
START
CR - Offset Acquiring Area V-Start
Position
500 0 - 1000 If not used: use Y's value
6 Y - GAIN AREA H START 50 0 - 1000
7 Y - GAIN AREA V START 500 0 - 1000
8 CB - GAIN AREA H START 800 0 - 1000
9 CB - GAIN AREA V START 500 0 - 1000
10 CR - GAIN AREA H START 700 0 - 1000
11 CR - GAIN AREA V START 500 0 - 1000
1 Image AREA H WIDTH YCBCR Level Acquiring Area 8 0 - 4095
13 Image AREA V HIGHT YCBCR Level Acquiring Area Height 9 0 - 4095
14 Y - OFFSET TARTGET 4 0 - 55
15 CB OFFSET TARGET 18 0 - 55
16 CR OFFSET TARGET 18 0-55
17 Y-GAIN TARGET 17 0-55
18 CB-GAINTARGET 37 0-55
19 CR-GAINTARGET 37 0-55
0 OFFSET torelance 1 1-55
1 GAIN torelance 1 1-55
Group
280
AutoPC Adjust
0 AutoPCAdjustEnable
Auto-PC Adj Operation Enable if Un-
supported Signal Input
0 0-1 0:Enabel, 1:Disable
1 Frequency Step Frequency Steps of Total Dot 1 0-3
Frequency Threshold Total Dot Freqency Threshold 5 0-10 0[]<-- - --> 10[Not matched]
3 Fine Phase Do Phase Adj after Total Dot Adj. 1 0-1 0;Excutes Fine Phase; 1:Not Excute
4 BLKDET Black Level Detection Area 1 0 - 3
Electrical Adjustments