Sanyo LC-XB200 Owner'S Manual Download Page 30

Page: 30 / 150

Chapter 4 Wired LAN configurations

Network Capture screen

Confirming the operation

Confirm that the projector has connected to the LAN properly.

Network Projector List

Search PJ button

1. Activate “Network Capture 5” which is installed into the computer connected to the LAN .
2. After “Searching projector” message appears, the name of the projector* appears on the Network

Projector List, then the network setting has completed properly.

When the name of the projector does not appear and error screen appears, the network has

not connected yet. Try searching again with the

Search PJ

button. If error screen appears again,

reconfirm the LAN setting. When the projector is set in the location separated by the router, see next
page.

When Firewall function (Anti-virus software) is effective, network projector may not be found. In that

case, disable the Firewall function and try searching again.

✳

If the projector is named, the name will be displayed. The name can be set with the following

procedures in “6. Basic setting and operation”

➔

“Initial setting” (p52) . If the projector is not named,

IP address of the projector will be displayed.

Summary of Contents for LC-XB200























































































































































Search results

Summary of Contents for LC-XB200

Reviews:

Related manuals for LC-XB200

Brands by name

Popular brands

Sanyo LC-XB200, Owner'S Manual

Search results

Summary of Contents for LC-XB200

Reviews:

Related manuals for LC-XB200

Brands by name

Popular brands