Network settings
1
Press
Z
and use
J
K
to Select
Setup
then press
OK
.
2
Use
H
I
J
K
to Select
Network settings
, then press
OK
.
3
Adjust the following items.
Manual network settings
1
Use
H
I
to Select
Manual network settings
, then press
OK
.
Proxy configuration
IP configuration
Wireless network setting
Network selection
Apps
Reset network settings
Home network
Setting status
Connection test
Manual network settings
Samba interactive TV settings
Network selection
2
Use
H
I
to Select
Network selection
, then press
OK
.
3
Use
H
I
to Select the desired setting, then press
OK
.
Wired
If you connect to an Ethernet Cable, select
Wired
to connect to the Internet.
Wireless
If you have a router with WPS function, select
Wireless
to connect to the Internet.
Wireless network setting
This menu is displayed only when you set
Wireless
in
Network
selection
. In order to use a wireless network, you must set up a
connection to the AP (e.g. Wireless Router).
2
Use
H
I
to Select
Wireless network setting
, then press
OK
.
Auto
Search for wireless networks automatically and select the SSID from the
list.
3
Use
H
I
to Select
Auto
, then press
OK
.
4
The list of wireless networks will be displayed. Use
H
I
to Select
the appropriate the SSID, then press
OK
.
Manually enter your SSID
Auto
Router 4
Router 3
Router 2
Router 1
Manual
WPS code
Simple Connect
●
If you select the SSID with , WEP
*2
/ WPA / WPA2 Key entry
screen will appear. Enter the WEP
*2
/ WPA / WPA2 key of the
selected wireless network using
H
I
J
K
, then press
OK
.
●
If you select the SSID has a WPS, the WPS setting screen will
appear. Use
H
I
J
K
to Select a setting, then press
OK
.
Simple Connect
Select this Setting if your Router has a Wi-Fi
Protected Setup (WPS) button. Start Scanning for
wireless networks on the TV after pressing the
WPS button on your Router. If Connection Test
fails, try
Simple Connect
again.
*1
If it fails then
refer to the Router’s Manual for more details.
WPS code
Select this Setting if your Router has a WPS but
does not have a WPS button. Enter the 8-digit
WPS PIN code shown on your TV in the Router
settings menu via PC before
Connect
is selected.
Manual
If your wireless network with authentication
setting (WEP
*2
, WPA or WPA2), WEP
*2
/ WPA /
WPA2 Key entry screen will appear. Enter the
WEP
*2
/ WPA / WPA2 key of the selected
wireless network using
H
I
J
K
, then press
OK
.
*1
WPS (Simple Connect) cannot be used when the security protocol
is set to WEP. Change the Access Point’s security mode from
WEP to WPA or WPA2 (recommended).
*2
WEP is not recommended to be used due to its Major security
flaws. Change the Security protocol on the Wireless Router to
WPA or WPA2 (recommended) mode.
Confirmation message will appear. Select
OK
to complete the settings.
Note(s)
●
For a wireless network with authentication setting, key icon appears to the right hand of the
SSID.
●
Signal icon shows the strength of the signal.
●
WEP
*2
/ WPA key appears as asterisks on the confirmation screen.
●
The wireless LAN supports following specifications.
–
Wireless standards: IEEE 802.11 a/b/g/n/ac
–
Frequency spectrum: 2.5GHz / 5GHz
–
Security protocol: WEP
*2
/ WPA / WPA2
39
.
English
Continued on next page.
Summary of Contents for FW50C85T
Page 55: ...A5LUZU2 ...
