background image

PRECAUTIONS

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE

TO EXCESSIVE MICROWAVE ENERGY

(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other micro-

wave source, and make repairs as necessary:
(1)Interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other damage),
(4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse.

(c) Before turning on microwave power for any service test or inspection within the microwave generating compart-

ments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and
connections.

(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and

transmission systems shall be repaired replaced, or adjusted by procedures described in this manual before
the oven is released to the owner.

SERVICE MANUAL      

Microwave Oven

     EM-C1900 (U.K)

REFERENCE NO.

 SM-6310022-00

Pro.Code No.   Model No.
437 623 00        EM-C1900UK

Foreword

Read this manual carefully, especially precaution on microwave energy, and follow the procedure
strictly,careless servicing and testing may expose yourself to the microwave energy leakage.

Summary of Contents for EM-C1900





























Reviews: