background image

- 9 -

Thermistor for duct of cavity top is operated by
over heating of 120

DISPLAY

E-21

E-31

Thermistor for lower magnetron or duct is
shorted.

Trouble

Situation

Buzzer will continuously beep tone. Blower
motor will stop immediately. Then oven will
stop heating.

Blower motor will stop immediately. Then
oven will stop heating.

E-32

Thermistor for lower magnetron or duct is dis-
connected or removed from connector socket.

Oven will stop heating.
Blower motor will be operated.

C. ERROR INDICATION
This model has some self diagnosis functions.

  Display shows "E" depending on the trouble.

CONDITION

        TROUBLE

      CHECK

RESULT

 REMEDY

Shorted

Replace

H.V Transformer

Shorted

Replace

H.V Capacitor

Shorted

Replace

Magnetron

Shorted

Replace

H.V Diode

Shorted

Replace

Fuse Diode

Poor
oscillation

 Replace

Magnetron

Low microwave
output

Rotation
stop

Repair or
replace

Rotation of top or
bottom anttena

Uneven heating

 U-10

Thermistor for Magnetron is operated by over
heating of 200

Buzzer will continuously beep tone.
Blower motor will stop immediately.
Then oven will stop heating.

U-50

The purpose of this function is to prevent opera-
tion when there is no food in the oven

Open and close the door, and then touch
the key before 1 minute passes

°C

°C

Summary of Contents for EM-C1800MK

























Reviews: