background image

CAUTION

  WARNING  TO SERVICE  TECHNICIANS

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING
    SERVICING TO AVOID POSSIBLE EXPOSURE TO

EXCESSIVE MICROWAVE ENERGY

(a)   Do not operate or allow the oven to be operated with the door open.
(b)   Make the following safety checks on all ovens to be serviced before activating the magnetron or other
        microwave source, and make repairs as necessary:
       (1)Interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other
       damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse.
(c)   Before turning on microwave power for any service test or inspection within the microwave generating
       compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,
       integrity, and connections.
(d)   Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation

and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual
before the oven is released to the owner.

(e)(i) A microwave leakage check to verify compliance with the Federal performance standard should be
       performed on each oven prior to release to the owner. (For U.S.A)
(e)(ii) A microwave leakage check to verify compliance with the Canadian Regulation, HEALTH AND WELFARE,

SOR/79-920 should be performed on each oven prior to release to the owner. (For CANADA)

  SUPPLEMENT OF

  SERVICE MANUAL      

Microwave Oven

EM-C160US

REFERENCE NO.SM-640180

See the Service Manual of EM-C180US(SM-640179)

except the items described in this Service Manual.

PRODUCT CODE NO.  437-453-00

Summary of Contents for EM-C160US















Reviews: