SANDVIK CH420:01 Installation Manual Download Page 78

Page: 78 / 110

6. Mechanical installation and connections

CH420:01

6.2.1

Rubber dampers

Adjust the mountings so that the rubber dampers are equally compressed.

WARNING!

Risk of crushing

If the crusher is mounted on rubber dampers there is a risk of crushing body
parts. Make sure that there is enough room for the crusher’s horizontal
movement. See

appendix A: Installation drawings

NOTE!

The crusher can be mounted directly on the foundation with foundation bolts.
Dynamic loads will then be much higher.

Foundation bolts are not supplied by Sandvik.

1
2
3

6
5

1 Locking nut

2 Washer

3 Upper fixing plate

4 Rubber compression

mounting

5 Screw

6 Washer

7 Lower fixing plate

8 Screw

9 Locking nut

Rubber damper, crusher and
motor on sub-frame

Rubber damper, crusher with
motor bracket

Summary of Contents for CH420:01















































































































Search results

Summary of Contents for CH420:01

Reviews:

Brands by name

Popular brands

SANDVIK CH420:01, Installation Manual

Search results

Summary of Contents for CH420:01

Reviews:

Brands by name

Popular brands