background image

KBox C-103-CFL-x  - User Guide, Rev. 1.0 

 

www.kontron.com 

 

// 6 

 

Symbols 

The following symbols may be used in this user guide 

 

 

 

DANGER indicates a hazardous situation which, if not avoided, 
will result in death or serious injury.

 

 

 

 

WARNING indicates a hazardous situation which, if not avoided, 
could result in death or serious injury.

 

 

 

 

NOTICE indicates a property damage message. 

 

 

 

CAUTION indicates a hazardous situation which, if not avoided, 
may result in minor or moderate injury.

 

 

 

 

Electric Shock!  
This symbol and title warn of hazards due to electrical shocks (>

 

60

 

V) when touching 

products or parts of products. Failure to observe the precautions indicated and/or 
prescribed by the law may endanger your life/health and/or result in damage to your 
material. 

 

 

 

ESD Sensitive Device! 
This symbol and title inform that the electronic boards and their components are sensitive 
to static electricity. Care must therefore be taken during all handling operations and 
inspections of this product in order to ensure product integrity at all times. 

 

 

 

HOT Surface! 
Do NOT touch! Allow to cool before servicing. 

 

 

 

Laser! 
This symbol inform of the risk of exposure to laser beam and light emitting devices (LEDs) 
from an electrical device.  Eye protection per manufacturer notice shall review before 
servicing. 

 

 

 

This symbol indicates general information about the product and the user guide. 

This symbol also indicates detail information about the specific product configuration.

 

 

 

 

This symbol precedes helpful hints and tips for daily use.

 

 

 

Summary of Contents for Kontron KBox C-103-0






























































































































Reviews: