background image

Company Name: 

Sandisk Corporation 

Eut: 

SanDisk SSD UATA 5000 1.8” 

Client Reference Number: 

QRTL06-334 

Work Order Number: 

2006137 

 

Compliance Report 

 

Page 9 of 17 

3 PRODUCT 

LABELING 

3.1 C-T

ICK 

M

ARK

 

The compliance label indicates that the product complies with the applicable standard and 
establishes a traceable link between the equipment and the manufacturer, importer or their 
agent responsible for compliance and for placing it on the Australian market. 

 

The requirements for labelling for specified electrical or electronic items are:

 

  

The mark 

to be used exactly as shown in the 

Radiocommunications (Compliance 

Labelling - Incidentals Emissions) Notice

. No variations are permitted. 

Location 

the mark and supplier identification should be a permanent feature placed 
on the external surface of the product as near as practical to the model 
identification. Where this is not practical, due to the size or nature of the 
product, the label may be placed on the labelling, packaging, warranty or 
instructions of the product. 

Method of 
marking 

the label shall be durably applied by any suitable means such as printing, 
painting, moulding, etching or engraving. 

Scale 

the mark shall be legible and visible to the unaided eye no smaller than 
3mm in diameter, with supplier identification characters no less than 1mm 
in height. 

Colour 

the label may be reproduced in any colour provided that visibility is assured 
through either contrast with the background colour or marking in relief 
(moulding, engraving etc). 

 

 

 

Note

   The C-Tick mark is a protected symbol for section 188A of the 

Radiocommunications Act 1992

 

 

Summary of Contents for SSD UATA 5000 1.8"



















Reviews: