Samsung WW8*J6 Series User Manual Download

Page: 20 / 56

20 English

Ins

tallation

Installation

Open the water tap and check if there
are any leaks around the connection
areas. If there are water leaks, repeat the
steps above.

•

If using a screw type of water tap,
connect the water hose to the water tap
as shown.

WARNING

Stop using the washing machine if there is a water leak, and contact a local Samsung service
centre. Otherwise, this may cause electric shock.

CAUTION

Do not stretch the water hose by force. If the hose is too short, replace the hose with a
longer, high-pressure hose.

NOTE

•

After connecting the water hose to the adaptor, check if it is connected properly by
pulling the water hose downwards.

•

Use a popular type of water taps. If the tap is square-shaped or too big, remove the
spacer ring before inserting the tap into the adaptor.

WW6000J(SEPM)-03580Q_EN (U.K).indd 20

2/9/2015 7:30:15 PM

Summary of Contents for WW8*J6 Series

























































Search results

Summary of Contents for WW8*J6 Series

Reviews:

Related manuals for WW8*J6 Series

Brands by name

Popular brands

Samsung WW8*J6 Series, User Manual

Search results

Summary of Contents for WW8*J6 Series

Reviews:

Related manuals for WW8*J6 Series

Brands by name

Popular brands