Fast Track Troubleshooting
Model: WA50**
Publication #DrWA50F9A Production Date 5/16/13
SM Revision Date:12/1/14
IMPORTANT SAFETY NOTICE
–
“For Technicians Only”
This service data sheet
is intended for use by persons having electrical, electronic, and mechanical experience and
knowledge at a level generally considered acceptable in the appliance repair trade. Any attempt to
repair a major appliance may result in personal injury and property damage. The manufacturer or
seller cannot be responsible, nor assume any liability for injury or damage of any kind arising from
the use of this data sheet.
Bulletins:
Support Information:
HELP: 1-888-751-4086 (Tech Sup. – ASC/SSD)
1-866-894-0637 (Tech Sup. - FE/ME)
GSPN:
http://service.samsungportal.com/EP/web/portal/jsp/EP_Default1.jsp
PLUS ONE:
http://my.plus1solutions.net/clientPortals/samsung
Quick Test Mode
To enter press Spin, Soil, & Power simultaneously with the power
off.
1. All LED’s light up and the washer beeps as it
enters the Quick Test Mode.
2. After the displaying the software version, LCD
will display Model information. If EEEE is displayed the PCB ass’y is
defective.
3. When the version is displayed, turn the Jog-Dial CCW so that the
version disappears. Press the following keys to test the various
components:
Press
Temp
to cycle through the Water Valves circuit test (lock the door
first) in this order: Pre-Wash, Bleach, Cold Main, Hot, & Steam, then off.
Press
My Cycle
to test Door Lock/Unlock circuit
Press
Spin
to test Circulation/Drain Pump.
Press
Soil
to test the Water/Steam Heater.
When either
Test or Spin
is displayed on the LCD, press
Start/Pause
to conduct the motor test.
In
Test mode
, you can test the clockwise and counterclockwise
movement of the motor.
In
Spin mode,
you can test the motor at a high rpm.
Service Mode:
This mode allows more detailed operation tests and
troubleshooting, to enter press Delay Start & Pre Soak
simultaneously with the power on.
In Service Mode the following tests can be performed:
Quick Spin Test:
Press and hold
Delay Start & Softener Option.
Note:
This accelerates the drum motor from 0 to max RPM in a
few minutes. Stay with the washer during this test, out of balance
detection may be bypassed.
Press
Start/Pause
during the test to
hold spinning speed for 10 minutes before going back to Quick Spin
Test Mode. Press and hold the
Delay Start & Softener Option
to
continue.
Cycle Count =
Press
Pre Soak
to see how many times the unit was
used.
Software # =
Press
Soil level
to see the SW version information.
Fault Code Test =
Press
Spin
to view the stored fault codes – then
turn
Jog Dial
to view error codes. Push
Start/Pause
while the code is
displayed to view the number of cycles since the error occurred, Push
Start/Pause to go back to faults.
Peripheral (Main PCB) input Tests:
1.
Select Eco Plus. Then turn the
Jog-Dial
so that the
Perm Press
LED
is turned on. Next, press
Start/Pause
and Water Temperature
will be displayed in Fahrenheit.
2.
Select Eco Plus. Then turn
Jog-Dial
so that the
Delicates/Hand
Wash LED
is turned on. The door status will be displayed (OP if open,
CL if closed).
3.
Select Eco Plus. Then turn
Jog-Dial
so that the
Quick Wash LED
is turned on. The door lock Switch status is be displayed (UL =
unlocked, Lo = locked).
4.
Select Eco Plus. Then turn
Jog-Dial
so that the
Pure Cycle LED
is
turned on and Water Level Frequency will be displayed.
EEPROM Clear
Entering Quick Test Mode will clear
EEPROM
Caution:
Error codes must be retrieved from
Service Mode
BEFORE
entering the
Quick Test mode or else they will be deleted
With the Power On
With the Power Off
