manualshive.com logo in svg

Samsung Techwin, User Manual, Page: 5 / 19

Share
Download
Samsung Techwin User Manual Download Page 5

3

Configure, fix and wire

1. Remove the foam packing pieces

3. Reassemble the speed dome

Protocol & Baud rate DIP switch table

Speed dome ID DIP switch table

2. Change protocol, baud rate and ID if required

Before proceeding with installation, the speed dome foam packing 
pieces must be removed. Remove the outer dome cover with the tool 
supplied and carefully remove the foam packing pieces. When 
handling the dome cover, always wear the gloves supplied to avoid 
getting fingerprints on the outer dome cover.

Refit the black inner dome cover and outer dome cover. If the 
lanyard safety wire was removed, it must be refitted before the dome 
cover is fixed.

The factory default setting is Pelco D, 2400, ID 1. Skip to section  
3 if these settings match your control equipment

Foam

Foam

Cover

Lanyard

1. Wearing the gloves and using the supplied 
tool, remove the outer dome cover.

1. Carefully unclip the black inner dome 

2. Locate the dip switches and set protocol 
and ID according to the table opposite.

2. Remove the foam pieces from the camera 
module.

Foam

1 2 3 4 5 6 7 8

1 2 3 4 5 6

ON

ON

ID

Protocol

Note: ID 0 should not be used. Where multiple speed domes
are connected, a unique ID must be assigned to each one.
Dip switches 9-10 are reserved and must not be changed.

1

2

3

4

5

6

7

8

ON

Factory default

switch positions

Speed dome ID is set 

using standard 
binary notation

1      2     3        

Protocol/Rate 

 

OFF   OFF  OFF      PelcoD,4800 bps
OFF   ON    OFF      AD,4800 bps
ON     ON    OFF      VC,9600 bps
OFF   OFF   ON       PelcoP,9600 bps
ON     OFF   ON       PelcoP,4800 bps
OFF   ON     ON       PelcoD,9600 bps
ON     ON     ON       PelcoD,2400 bps

Note: Dip switches 4-6 are reserved 
and must not be changed.

 1     2     3     4      5     6     7     8      9     10    DIP
 1     2     4     8    16   32   64  128    –      –  

VAL/ID

ON   OFF OFF  OFF  OFF  OFF  OFF  OFF      

OFF  ON  OFF  OFF  OFF  OFF  OFF  OFF      

–      –      2

ON    ON  OFF  OFF  OFF  OFF  OFF  OFF      

–      –      3

OFF OFF  ON   OFF  OFF  OFF  OFF  OFF      

–      –      4

ON   OFF  ON   OFF  OFF  OFF  OFF  OFF      

–      –      5

OFF  ON   ON   OFF  OFF  OFF  OFF  OFF      

–      –      6

ON    ON   ON   OFF  OFF  OFF  OFF  OFF      

–      –      7

OFF  OFF OFF  ON   OFF  OFF  OFF  OFF      

–      –      8

 –

       

–     –     –      –     –     –     –      –      –     –

ON    ON    ON    ON    ON    ON    ON    ON                        

255

–      –      1

Summary of Contents for Techwin




















Reviews:

No comments