Samsung SyncMaster 460TSN Page 44 User Manuals Download

Page: 44 / 167

Connect an HDMI cable to

[HDMI IN 2 (MAGICINFO)]

[HDMI IN 1]

on the

product and the HDMI output port on a digital device.

Press

SOURCE

on the product or remote control and select "

HDMI1

HDMI2

Note

HDMI

mode, only PCM format audio is supported.

Connecting Using a DVI to HDMI Cable

Connect a DVI-HDMI cable to

[HDMI IN 2 (MAGICINFO)]

[HDMI IN 1]

and

the DVI output port on the digital device.

Connect the red and white jacks of an RCA to stereo (for PC) cable to the same
colored audio output terminals of the digital output device, and connect the op-
posite jack to the

[RGB/DVI/DP/HDMI AUDIO IN]

terminal of the LCD Display.

Press

SOURCE

on the product or remote control and select "

HDMI1

HDMI2

Connecting a DVD Player

Connections

Summary of Contents for SyncMaster 460TSN








































































































































































Search results

Summary of Contents for SyncMaster 460TSN

Reviews:

Related manuals for SyncMaster 460TSN

Brands by name

Popular brands

Samsung SyncMaster 460TSN, User Manuals

Search results

Summary of Contents for SyncMaster 460TSN

Reviews:

Related manuals for SyncMaster 460TSN

Brands by name

Popular brands