Samsung SyncMaster 460TSN Page 143 User Manuals Download | Manualshive

Page: 143 / 167

background image

Note

When there are two or more BMP images, they are displayed on the screen using a slideshow.

•

It is recommended that the playback interval between two BMP images in the slideshow
should be one second. The image extraction probability will decrease with other playback
intervals.

•

A BMP image might not be extracted if it is covered by another image (for example, the mouse
pointer).

3.

If a more recent version than the current software version is detected, you will be asked whether
to upgrade the current software. If you select <

Yes

>, the upgrade is performed.

4.

When the software upgrade is completed, the product is turned off and on automatically.

Note

•

This only operates with a digital signal, such as in

DVI

,

HDMI1

, or

HDMI2

mode. (The input

resolution must be identical to the panel resolution.)

•

In

HDMI1

and

HDMI2

modes, the timing values used for both the PC and TV are only supported

if the

Edit Name

is set to

PC

or

DVI PC

.

•

This is only supported if the

Size

is set to

16:9

.

Setup Reset

Reset all the values for a setting.

Reset All

Adjusting the LCD Display

«
...
141
142
143
144
145
...
»

Summary of Contents for SyncMaster 460TSN








































































































































































Reviews:

No comments

Related manuals for SyncMaster 460TSN

ENTER 42 PRO X2

Brand: Dyon Pages: 68

Brand: TCL Pages: 16

Brand: Transonic Pages: 17

26MF605W series

Brand: Magnavox Pages: 42

Brand: Sceptre Pages: 12

Brand: Walker Pages: 39

Brand: Dynex Pages: 2

Brand: FUNAI Pages: 20

Brand: Pyle Pages: 26

Brand: Grundig Pages: 18

Brand: Farenheit Pages: 13

Brand: Panasonic Pages: 359

Brand: Samsung Pages: 105

Brand: Samsung Pages: 98

Brand: Samsung Pages: 289

Brand: JVC Pages: 48

Brand: JVC Pages: 48

Brand: JVC Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands