Samsung SyncMaster 460TSN Page 114 User Manuals Download

Page: 114 / 167

Color Tone

Note

Not available when

Dynamic Contrast

is set to

The Color tones can be changed.

Off

Cool

Normal

Warm

Custom

Note

•

If you set the

Color Tone

Cool

Normal

Warm

, or

Custom

, the

Color Temp.

function is

disabled.

•

If you set the

Color Tone

Off

, the

Color Control

function is disabled

•

By adjusting the picture using the

Color Tone

function,

Mode

will change to

Custom

mode.

Color Control

Adjusts individual Red, Green, Blue Color balance.

Note

Not available when

Dynamic Contrast

is set to

Red

Green

Blue

Color Temp.

Adjusting the LCD Display

Summary of Contents for SyncMaster 460TSN








































































































































































Search results

Summary of Contents for SyncMaster 460TSN

Reviews:

Related manuals for SyncMaster 460TSN

Brands by name

Popular brands

Samsung SyncMaster 460TSN, User Manuals

Search results

Summary of Contents for SyncMaster 460TSN

Reviews:

Related manuals for SyncMaster 460TSN

Brands by name

Popular brands