background image

2

A s s e m b l i n g   Pa r t s

Assembled Vacuum Cleaner Parts

The assembled cleaner will look
like the illustration to the left.

1. Handle
2. Power switch
3. Quick release cord hook
4. Post-Motor Filter
5. Crevice tool
6. Handle release
7. Carrying handle
8. Hose
9. Extension wand
10. Combination tool
11. Cyclone-Lever
12. Dirt Cup
13. Filter Cup
14. Upper Tank
15. Louvers
16. Hose Wand Base
17. Height Adjustment Dial
18. Hose Clip

WARNING!

OPERATE  THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE.

Front

Back

Step 1. Attaching the Handle

Step 2. Attaching the Hose and Tools

Stand the vacuum upright and
slide the base of the handle
firmly into the grooves at the top
of the vacuum body.

Insert the screw provided into the
existing hole. Tighten the screw
securely with a screwdriver.
Before securing the handle,
please check that the handle is
fitted to the vacuum body and
make sure there’s no gap.

Slide the end of the hose
wand with tabs into the Hose
Wand Base.

Slide the extension wand
and the crevice tool together
into the storage clip.

1-1

1-2

1-3

1-4

1-5

Unless power switch is off or unplugged, the floor
brush will rotate while you use your vacuum
cleaner on carpet or floor.
For above floor cleaning, the floor brush will
continue to rotate but is raised above floor.
To prevent carpet damage, do not lean on the
vacuum or let the powerfoot tilt forward.

CAUTION

DJ68-00294L(0.5)  2009.5.21 11:4 AM  페이지3    in

Summary of Contents for SU2913









Reviews: