Samsung SNB-9000 User Manual Download Page 23

Page: 23 / 152

English

_23

●

INST

ALLA

TION & CONNECTION

Connecting to the I/O port box

Connect the Alarm I/O signal to the corresponding port of the rear port box.

Connecting an external RS-485/RS-232 device

Connect the camera with an external device using the [

Tx, Rx, RS-485-, RS-485+

] ports.

You can control the pan/tilt operations of the camera via RS-485/RS-232 communications.



The GND connection is recommended for RS-485/RS-232 communications. If you encounter a
communication failure, connect the GND pin as appropriate to correct the GND level between camera and
external device.

To connect the external sensor

Connect one strand of each signal line (2-strand) of the sensors to the [

Alarm in 1/2

] port,

and connect the other strand to the [

GND

] port.



Be attention not to connect an Alarm in signal higher than 6V.

Alarm In Wiring Diagram

ACT

LINK

FOCUS

1 2 3 4 5 6 7 8 9 10

1: GND
2: Tx
3: Rx

4: RS-485 -
5: RS-485 +
6: EXT D/N

7: Alarm in 1
8: Alarm in 2

9: Alarm Out
10: COM

LINK

FOCUS

1 2 3 4 5 6 7 8 9 10

1: GND
2: Tx
3: Rx

4: RS-485 -
5: RS-485 +
6: EXT D/N

7: Alarm in 1
8: Alarm in 2

9: Alarm Out
10: COM

Sensor

RESISTOR

ALARM IN

RESISTOR

VCC_3.3V

GND

MLCC

TRANSISTOR

External

connection

Inside of the camera

RESISTOR

DIODE

Summary of Contents for SNB-9000

























































































































































Search results

Summary of Contents for SNB-9000

Reviews:

Samsung SNB-9000, User Manual, Page: 23 / 152

Search results

Summary of Contents for SNB-9000

Reviews: