manualshive.com logo in svg

Samsung SNB-8000, User Manual, Page: 94 / 172

Share
Download
Samsung SNB-8000 User Manual Download Page 94

setup screen

94_

 setup screen

to Set Day/night (Snv-8080)
1. 

Select <

Day/night

>.

2. 

Select each item and set it properly.

 

•

Day/Night : Mode is used to adjust 

the color of Color or Black and 

White.

 - Color : The video is always output in 

color.

 - B/W : The video is always output in 

black and white.

 - Auto : Normally, it is set to Color but to B&W under low luminance at night.

 

`

If AGC of the <

Exposure

> menu is set to <

Off

>, the day/night mode cannot be set to <

Auto

>.

 - External : It controls the color of the video when the alarm input terminal is synchronized 

with an external device.

 - Schedule : Set the time during which the camera is operated in the color mode.

 

•

Dwell Time : It specifies the period for which the selected brightness condition 

must be maintained to switch the lighting mode from Day to Night or vice versa.

 

•

Duration : It specifies the interval of lighting mode conversion.

 

•

Alarm in : The video is set to Color or B/W as the alarm sensor is open or closed.

 

`

If the Day/Night mode is set to External Input, the alarm input function of the Event-Alarm Input 

page is disabled.

 

•

Activation time : Configure a schedule of operation.

 

`

If it is set, the Color mode is maintained from 00 second of the starting time to 59 second of the 

ending time. 

 

J

 

`

The Day/Night mode may not operate properly if the lens installed in the camera and the lens set 

in <

Iris

> of the <

Exposure

> menu don’t match.

 

`

If you switch the day/night mode, the MD/VA event cannot be detected.

Summary of Contents for SNB-8000













































































































































































Reviews:

No comments