Samsung SNB-8000 User Manual Download Page 41

Page: 41 / 172

English

_41

●

aLL

ation & connection

connecting an external rS-485 device (SnB-8000)

Connect the camera with an external device using the [

rS-485 +, -

] ports.

You can control the pan/tilt operations of the camera via RS-485 communications.

The GND connection is recommended for RS-485 communications. If you encounter a communication

failure, connect the GND pin as appropriate to correct the GND level between camera and external device.

connecting to the i/o port box (Snv-8080)

Connect the Alarm I/O cable to the corresponding port of the inner port box.

•

ALARM OUT : Used to connect the alarm output signal.

•

ALARM IN : Used to connect the alarm input sensor or external day/night sensor.

•

GND : Common terminal to connect alarm signals.

Alarm

(Warning lamp)

Sensor

Summary of Contents for SNB-8000













































































































































































Search results

Summary of Contents for SNB-8000

Reviews:

Samsung SNB-8000, User Manual, Page: 41 / 172

Search results

Summary of Contents for SNB-8000

Reviews: